Whirlpool Cabrio WTW6200S страница 51 Скачать руководство пользователя

Страница: 51 / 84

4-11

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

WARNING

1. Unplug washer or disconnect power.
2. Raise the cabinet top (see step 3e on

page 4-4 for the procedure).

To remove the basket:

a) Pull the liquid fabric softener dispens-

er off the top of the agitator.

d) Pull the bottom half of the agitator

straight up and off the drive motor
shaft and remove it.

b) Pull the barrier cap out of the agitator

and remove it.

c) Using a ratchet with a 7/16

socket

and a 12

extension, remove the hex-

head bolt from the agitator, then lift
the top half of the agitator out of the
washer.

Fabric Softener

Dispenser

Barrier Cap

Agitator Bolt

Agitator (Bottom Half)

Agitator (Top Half)

REMOVING THE BASKET & BASKET HUB

Continued on the next page.

Содержание Cabrio WTW6200S





















































































Результаты поиска

Содержание Cabrio WTW6200S

Отзывы:

Похожие инструкции для Cabrio WTW6200S

Бренды по названию

Популярные бренды

Whirlpool Cabrio WTW6200S, Руководство пользователя

Результаты поиска

Содержание Cabrio WTW6200S

Отзывы:

Похожие инструкции для Cabrio WTW6200S

Бренды по названию

Популярные бренды