Whirlpool Cabrio WTW6200S Скачать руководство пользователя страница 65

Страница: 65 / 84

6-1

DIAGNOSTICS & TROUBLESHOOTING

DISPLAY FAULT / ERROR CODES

DISPLAY

(Saved Code)

EXPLANATION AND RECOMMENDED PROCEDURE

(F30)

Long Fill

flashes when the water level does not change for a period of time after the valves are turned on OR water has disengaged

the basket but control does not detect a water level change.

•

Is water supply connected and turned on?

•

Are hose screens plugged?

•

Is water entering the tub? If so check pressure hose connection to machine/motor control.

•

See TEST #2.

(F32)

Long Drain

flashes when the water level does not change after the drain pump is on.

•

Is the drain hose or the drain pump clogged?

•

Is the drain hose height greater than 96˝ ?

•

Is the pump running? If not, see TEST #7.

(none)

Unbalanced Load

is displayed when the machine/motor control detects an off-balance load, and is steady on while the washer runs a

mini-cycle to rebalance the load.

•

Display clears if mini-cycle successfully rebalanced the load.

•

If the mini-cycle is unsuccessful,

will flash until the door lid is opened, allowing the customer to view and redistribute

the load.

(F70)

Overloaded

flashes when the machine/motor control detects a load size that exceeds the washer’s capacity.

•

Open the door lid to clear display, remove excess laundry, then restart the cycle.

(F71)

Suds Detection

is displayed when the machine/motor control, by analyzing drag on the basket, detects a suds-lock condition, and is steady

on while the control then runs a mini-clean out cycle. If the clean out cycle is unable to correct the over-sudsing problem, the
cycle ends and

flashes in the display. This may signify:

•

Excessive detergent usage.

•

Basket cannot engage during drain step.

•

Mechanical friction on drive mechanism, not allowing basket to engage.

Continued on the next page.

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.

WARNING

Содержание Cabrio WTW6200S





















































































Результаты поиска

Содержание Cabrio WTW6200S

Отзывы:

Бренды по названию

Популярные бренды

Whirlpool Cabrio WTW6200S, Руководство пользователя

Результаты поиска

Содержание Cabrio WTW6200S

Отзывы:

Бренды по названию

Популярные бренды