Whirlpool Cabrio WTW6200S страница 66 Скачать руководство пользователя

Страница: 66 / 84

6-2

(F81)

Open/Close Door Lid

Lid flashes when the following conditions occur:

•

User presses START with lid open.

•

User presses START after 2 consecutive machine cycles without opening lid.

•

The machine/motor control cannot detect the lid switch opening and closing properly.

See TEST #8.

(none)

Pump Out (lid opened)

flashes when drain pump begins pumping out water from tub upon activation by the door lid having been left open for

more than 10 minutes.

•

Close door lid to stop drain pump.

If drain pump turns on when there is no water in tub,

Hot, Cold Reversed

flashes when the hot and cold inlet hoses are reversed.

•

Make sure inlet hoses are connected correctly.

(F80, 82,
84, 85)

Door Lock Failure

flashes if the following conditions occur:

•

Door lid is not closed completely due to interference.

•

Wash media buildup is preventing the lock bolt from extending.

•

Machine/motor control detects open door lid switch when attempting to lock.

•

Machine/motor control cannot determine if door lid is in a locked state.

See TEST #8.

(F83)

Door Unlock Failure

flashes if the following conditions occur:

•

Excessive force on door lid is preventing lock bolt from retracting.

•

Wash media buildup is preventing lock bolt from retracting.

•

Machine/motor control cannot determine if door lid is in an unlocked state.

See TEST #8.

(F60-68)

Primary Control Failure

then

flashes when there is a primary control failure. Replace the machine control assembly.

See Accessing & Removing the Electronic Assemblies.

(F2)

Keypad/User Interface Failure

then

flashes when in:

•

Diagnostics Test mode if a stuck key is detected.

•

Standby mode if there is a user interface mismatch.

DISPLAY

(Saved Code)

EXPLANATION AND RECOMMENDED PROCEDURE

See TEST #4.

Содержание Cabrio WTW6200S





















































































Результаты поиска

Содержание Cabrio WTW6200S

Отзывы:

Похожие инструкции для Cabrio WTW6200S

Бренды по названию

Популярные бренды

Whirlpool Cabrio WTW6200S, Руководство пользователя

Результаты поиска

Содержание Cabrio WTW6200S

Отзывы:

Похожие инструкции для Cabrio WTW6200S

Бренды по названию

Популярные бренды