Whirlpool Cabrio WTW6200S страница 71 Скачать руководство пользователя | Manualshive

Страница: 71 / 84

background image

6-7

Press and release:

2nd RINSE

or EXTRA RINSE

Door locks, lid lock indicator turns on.

Repeat

Door unlocks, lid lock indicator turns off.

•

•

Manual: Door Switch

Opening  the  door  should  cause  the  Clothes
Clean  or  Done  status  indicator  to  turn  off.
Closing  the  door  should  cause  the  indicator
to turn on.

If Clothes Clean or Done indicator does not
turn off or on, go to TEST #8.

Manual: Door Lid Lock
NOTE:

Door must be closed. If door is not

closed, an invalid button press beep will oc-
cur when performing next step.

•

If door does not lock or unlock, go to TEST
#8.

•

Press and release:

SPIN SPEED, WATER

LEVEL or LOAD SIZE

Motor/basket spins at 23 rpm.

Repeat

Motor/basket spins at 530 rpm.

Repeat

Motor/basket spins at 1000 rpm.

Repeat

Motor turns off.

•

•
•
•

Press and release:

SOIL LEVEL

Gentle wash action.

Repeat

Normal wash action.

Repeat

Heavy wash action.

Repeat

Motor turns off.

•

•
•
•

Manual: Motor
Rotor Position Sensor (RPS):

Uses Wash,

Rinse and Spin indicators to detect the three
rotor position sensors. Console may have up
to two of these indicators on at one time when
the basket is not moving. Open door and ro-
tate basket by hand. The Wash, Rinse and
Spin status indicators should toggle on and
off according to direction the basket is being
turned.

If none of these indicators are on go to
TEST #3.

Spin:

To activate Spin, door must be closed

with door lock enabled. See Manual: Door Lid
Lock.

NOTE:

If door is not closed, an invalid button

press beep will occur when performing next
step.

•

Agitate:

Water must cover the wash plate (or

agitator vanes) to ensure the basket is float-
ing prior to agitation. Enabling agitation with-
out enough water may cause a fault condition
to occur. See Manual: Water Valves.

NOTE:

Indicators above button scroll from

top to bottom.

If motor fails to agitate, go to TEST #3.

•

NOTE:

Indicators above button scroll from

top to bottom.

If motor fails to spin, go to TEST #3.

•

ACTIVATION OF CONSOLE AND
INDICATORS DIAGNOSTIC TEST MODE

This test checks the cycle selector knob, indi-
cators, buttons, two-digit display and beeper.
1. Plug in washer or reconnect power.
2. Read through step 3 before continuing.

From Standby (Off) Mode press and re-
lease (key-dance) the following buttons
within 4 seconds:

If successful, two-digit

dt

will display and

you will have 5 seconds to complete next
step.

3. Within 5 seconds of

dt

showing in display,

press START (all indicators in display are
illuminated and

88

is displayed).

Press  START  a  second  time.  This
turns off status indicators and two-digit
display  (all  other  indicators  remain  il-
luminated).
Press  START  a  third  time.  This  turns
on status indicators and two-digit dis-
play (all indicators are illuminated).

4. Rotate WASH CYCLE selector back and

forth. Indicators will toggle on (or off).

•

•

SOIL

LEVEL

WASH/RINSE

TEMP

SOIL

LEVEL

WASH/RINSE

TEMP

«
...
69
70
71
72
73
...
»

Содержание Cabrio WTW6200S





















































































Отзывы:

Нет отзывов

Похожие инструкции для Cabrio WTW6200S

Бренд: Campbell Hausfeld Страницы: 18

Бренд: Kärcher Страницы: 18

Aqualtis AQSD 291 U

Бренд: Hotpoint Ariston Страницы: 72

Бренд: Shark Pressure Washers Страницы: 28

Бренд: Fagor Страницы: 112

Бренд: Estate Страницы: 1

Бренд: Kärcher Страницы: 20

ConturaMonoPLUS

Бренд: jobst Страницы: 12

Бренд: Daewoo Страницы: 50

Super 20 CL8761

Бренд: Speed Queen Страницы: 41

Бренд: F.F. Group Страницы: 64

Бренд: Lavor Страницы: 56

Бренд: Sindelen Страницы: 16

Бренд: Porter & Charles Страницы: 3

Бренд: Samsung Страницы: 56

WW75H5200E Series

Бренд: Samsung Страницы: 88

Бренд: Samsung Страницы: 56

Бренд: Candy Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды