Whirlpool Cabrio WTW6200S страница 70 Скачать руководство пользователя | Manualshive

Страница: 70 / 84

background image

6-6

2. If done successfully, a single beep oc-

curs and the two-digit display shows one
of the following console ID#s:

06, 08, 12,

13, 14, 15, 16, 17, 18, 19, 20, 21, 44, 45,
46, 47, 48, 49, 60, 61, 62

for 3 seconds,

then displays

00

and the Add A Garment

indicator LED flashes. See Diagnostic:
Manual.

If entry into Manual Diagnostic mode
is successful, but none of the console
ID#s above are displayed, replace the
user interface assembly. See Access-
ing & Removing the Electronic Assem-
blies.

DIAGNOSTIC: Manual

Assumes Manual Diagnostic mode has been
entered, two-digit display shows 00, and ADD
A GARMENT indicator is flashing.

NOTE:

If there is no activity (button press,

cycle select) within 5 minutes, the control au-
tomatically exits Diagnostic mode and enters
standby mode.

Manual: Water Valves
To check FRESH valve

select or press the

following:

WHITES/WHITES  •  START  (turns  on
Fresh  valve,  cycle  indicator  flashes)  •
WASH/RINSE TEMP (enables fill of Hot,
Warm,  Cold  or  no  water  according  to
WASH/RINSE  TEMP  selection  and  in-
dicator) • START (turns off Fresh valve,
cycle indicator is steady on).

To check DETERGENT valve

select or press

the following:

HEAVY  DUTY  •  START  (turns  on  De-
tergent  valve,  cycle  indicator  flashes)    •
WASH/RINSE TEMP (enables fill of Hot,
Warm,  Cold  or  no  water  according  to
WASH/RINSE TEMP selection and indi-
cator) • START (turns off Detergent valve,
cycle indicator is steady on).

•

To check FABRIC SOFTENER valve

select

or press the following:

NORMAL • START (turns on Fabric
Softener valve, cycle indicator flashes) •
WASH/RINSE TEMP (enables fill of Hot,
Warm, Cold or no water according to
WASH/RINSE TEMP selection and indi-
cator) • START (turns off Fabric Softener
valve, cycle indicator is steady on).

To check BLEACH valve

select or press the

following:

CASUAL • START (turns on Bleach valve,
cycle  indicator  flashes)  •  WASH/RINSE
TEMP  (enables  fill  of  Hot,  Warm,  Cold
or  no  water  according  to  WASH/RINSE
TEMP  selection  and  indicator)  •  START
(turns off Bleach valve, cycle indicator is
steady on).

NOTE:

Washer can only fill cold through

Bleach valve.

If any valve fails to turn on go to TEST #2.

Manual: Pumps

•

Models with Push-button cycles:

Press and release:

CLEAN WASHER

or DRAIN & SPIN

•

•

•
•

•

•

•
•

Turns on recirculation pump, indicator is

steady on.

Repeat

Turns off recirculation pump, indicator

turns off.

Repeat

Turns on drain pump, indicator flashes.

Repeat

Turns off drain pump, indicator turns off.

Models using Cycle Selector:

Select CLEAN WASHER or DRAIN & SPIN.
Press and release:

START

Turns on recirculation pump, cycle

indicator is steady on.

Repeat

Turns off recirculation pump, indicator

turns off.

Repeat

Turns on drain pump, indicator flashes.

Repeat

Turns off drain pump, indicator turns off.

If pumps fail to turn on go to TEST #7.

•

«
...
68
69
70
71
72
...
»

Содержание Cabrio WTW6200S





















































































Отзывы:

Нет отзывов

Похожие инструкции для Cabrio WTW6200S

Бренд: Fasa Страницы: 17

K 4.650 Jubilee

Бренд: Kärcher Страницы: 18

Бренд: Kärcher Страницы: 184

Бренд: BCP Страницы: 16

Бренд: Simpson Страницы: 76

Бренд: Gibson Страницы: 14

Бренд: Maytag Страницы: 48

Бренд: Asko Страницы: 16

Бренд: Zanussi Electrolux Страницы: 28

Бренд: Gaggenau Страницы: 48

Бренд: V-ZUG Страницы: 52

PowerWash 2200W

Бренд: Vax Страницы: 24

Бренд: UNITED Страницы: 32

DW60A6092 Series

Бренд: Samsung Страницы: 31

DW60M9530F Series

Бренд: Samsung Страницы: 56

Бренд: Indesit Страницы: 16

Бренд: Hotpoint Страницы: 16

Бренд: Hotpoint Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды