Whirlpool Cabrio WTW6200S страница 61 Скачать руководство пользователя | Manualshive

Страница: 61 / 84

background image

5-1

COMPONENT TESTING

Before testing any of the components, perform
the following checks:

The most common cause for control failure
is corrosion on connectors. Therefore, dis-
connecting and reconnecting wires will be
necessary throughout test procedures.
All tests/checks should be made with a
VOM or DVM having a sensitivity of 20,000
ohms-per-volt DC, or greater.

•

•

WATER INLET/ DISPENSER
VALVE ASSEMBLY

Check  all  connections  before  replacing
components,  looking  for  broken  or  loose
wires, failed terminals, or wires not pressed
into connectors far enough.
Resistance  checks  must  be  made  with
power  cord  unplugged  from  outlet,  and
with wiring harness or connectors discon-
nected.

•

•

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.

WARNING

2. Disconnect the wire connector from the

component under test.

3. Set the ohmmeter to the R x 1 scale.
4.

Water Inlet / Dispenser Solenoids:

Touch

the ohmmeter test leads to each of the wa-
ter inlet/dispenser valve solenoid terminals.
The meter should indicate between 700
and 900

Ω

. If the reading is outside this

range, replace the valve assembly.

5.

Thermistor:

Touch the ohmmeter test

leads to the thermistor terminals. The
meter should indicate as shown in the
following chart.

Thermistor

Detergent

Dispenser

Bleach Dispenser

Hot & Cold

Water Inlet Valves

THERMISTOR RESISTANCE

Temperature

Resistance

(Ohms)

Temperature

Resistance

(Ohms)

10°C (50°F)

19k–20.5k Ω

38°C (100°F)

5.6k–5.9k Ω

16°C (60°F)

15k–15.7k Ω

44°C (110°F)

4.6k–4.9k Ω

21°C (70°F)

11.7k–12.2k Ω

49°C (120°F)

3.6k–3.8k Ω

27°C (80°F)

9.1k–9.5k Ω

55°C (130°F)

2.9k–3.1k Ω

32°C (90°F)

7.2k–7.6k Ω

Refer  to  page  4-4  for  the  procedure  for  ac-
cessing  the  water  inlet/dispenser  valve  as-
sembly.
1.  Unplug washer or disconnect power.

Fresh Fill

Inlet Valve

«
...
59
60
61
62
63
...
»

Содержание Cabrio WTW6200S





















































































Отзывы:

Нет отзывов

Похожие инструкции для Cabrio WTW6200S

Бренд: Ignis Страницы: 28

Бренд: Dacor Страницы: 29

Бренд: Zanussi Страницы: 28

Бренд: Magic Chef Страницы: 30

Бренд: Magic Chef Страницы: 8

Бренд: Kärcher Страницы: 16

Бренд: Midea Страницы: 10

INDEPENDENT 2800

Бренд: Lavor Страницы: 124

Бренд: Admiral Страницы: 6

Бренд: Progress Страницы: 72

Бренд: Silverline Страницы: 88

Бренд: Magic Chef Страницы: 12

Бренд: Parkside Страницы: 56

Бренд: A.O. Smith Страницы: 6

Бренд: Lavorwash Страницы: 20

Бренд: Kärcher Страницы: 180

Бренд: NABO Страницы: 32

Бренд: Saivod Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды