background image

14 

Document #: LIN_GO_SM_IMPLOPRO_S1600_INTL_4605727 – 9/20

Installation 

Section 2

UNCRATING
When you have all the crates unloaded, open the crates and 

remove the plastic covers. Inspect at once for concealed 

damage. If anything appears to be damaged, contact the 

appropriate persons immediately to file a damage claim. 

After completing this inspection, finish unpacking the oven 

and all other components. Be sure to remove the packing 

cardboard from the plenum shroud. Move all components 

inside near the area where they will be assembled in the 

order in which they will be assembled.
THE OVEN WILL CLEAR THROUGH A 30" (762 MM) 

DOORWAY BY USING THE FOLLOWING PROCEDURE:

1.  Remove conveyor; see “Conveyor Removal for Cleaning” 

in 

Section 4

 for instructions. (Some units may have 

conveyor packed separately.)

2.  Remove front doors by lifting the doors from the hinge 

plates.

3.  Remove finger assembly and baffles from inside the 

oven.

4.  Place oven front on a four-wheel moving dolly and it 

will clear a 30" (762 mm) doorway.

NOTE: Use care not to damage hinge plates on oven front.

Notice

Do not lift the ovens using the control enclosure. Lift 

from the main oven cavity only. Damage may occur to 

the controls of the oven if lifted by the control enclosure.

Manual Gas Valve Installation

When installing the gas valve that is supplied with the 

oven it is our suggestion that an elbow be placed on the 

oven pipe first if one is not already installed. This will allow 

the flexible hose to be attached in a downward direction, 

eliminating possible stress to the hose.

Assembly Instructions

1.  For Single Stack Ovens: The stand is a 40" (1016 mm) 

x 47" (1194 mm) rectangle. Set it in place with a 40" 

side facing out. This will be the front of the oven. Ovens 

on casters require a level floor. NOTE: The oven top is 

packed with oven stand. Remove top from stand before 

assembly.

P/N 1612

2.  Oven Placement: Remove the oven from the dolly and 

set it on the stand. The control panel should be on the 

right rear as you face the oven. Be sure that the oven 

sets squarely on the stand and is fully seated. For a 

single oven, install top and duct cap onto rear cover. 

Содержание Lincoln Impinger 1600 Series





















































Отзывы: