Welbilt Lincoln Impinger 1600 Series Скачать руководство пользователя страница 13

Страница: 13 / 52

Document #: LIN_GO_SM_IMPLOPRO_S1600_INTL_4605727 – 9/20

Section 2

Installation

RESTRAINT REQUIREMENT – ALL OVEN(S) ON CASTERS

DANGER

Legs or casters must be installed and the legs or casters

must be screwed in completely to prevent bending.

When casters are installed the mass of this unit will allow

it to move uncontrolled on an inclined surface. These

units, when permanently connected, must be tethered/

secured to comply with all applicable codes, so that

stress is not transmitted to the electrical supply conduit.

• The installation shall be made with a gas connector that

complies with the Standard for Connectors for Movable

Gas Appliances, ANSI Z21.69 latest version, and a quick

disconnect device that complies with the Standard for

Quick Disconnect Devices for Use With Gas Fuel, ANSI

Z21.41 latest version.

IN CANADA: The installation shall be made with gas

connectors that comply with Canadian Code CSA 6.16

latest version and quick disconnects complying to

Canadian Code CSA 6.9 latest version.

IN AUSTRALIA: To be installed in accordance with AS

5601-2004 and 4563-2004 Gas Installation Code.

• The installation of the restraint must limit the

movement of the oven(s) without depending on the

connector, the quick disconnect device, or its associated

piping to limit the oven movement.

• If the restraint must be disconnected during

maintenance or cleaning, it must be reconnected after

the oven has been returned to its originally installed

position.

Procedure

1. Screw lifting eye end “B” of cable assembly to hole “A”.
2. Screw eye bolt end “C” of cable assembly to stud in wall

“D” or floor anchor “E”.

NOTE: Installation point is the same for single, double, or

triple stacked ovens.

Wall

Floor

Stud

BACK OF DOUBLE OVEN

Wall

Floor

Stud

Installation

The instructions that follow are intended as a guide for

preparing for the installation of the Impinger® Conveyor

Ovens, Series 1600. First and foremost, each crate should

be examined before signing the Bill of Lading to report any

visible damage by the trucker in transit, and to account for

the proper number of crates.

UNLOADING
When the oven arrives it should consist of:

1. A crate containing oven body, conveyor, fingers, crumb

pans, and pan stops. (Some models may have the

conveyor packed separately.)

2. A package containing the stand and top.

It is recommended that you have a material-handling

device available to unload.
NOTE: DO NOT LIFT EXCESSIVE WEIGHT!
IF THERE IS APPARENT DAMAGE:
UNITED STATES AND CANADA: Arrangements should

be made to file a claim against the carrier, as Interstate

Commerce Regulations require that the consignee initiate

a claim.
ALL SHIPMENTS TO OTHER COUNTRIES: Freight terms will

be developed and extended on an individual basis.
Proper and secure storage facilities should be arranged for

the oven(s). If necessary, protect it from outdoor or damp

conditions at all times before installation.

Содержание Lincoln Impinger 1600 Series





















































Результаты поиска

Содержание Lincoln Impinger 1600 Series

Отзывы:

Похожие инструкции для Lincoln Impinger 1600 Series

Бренды по названию

Популярные бренды

Welbilt Lincoln Impinger 1600 Series, Международное руководство по обслуживанию

Результаты поиска

Содержание Lincoln Impinger 1600 Series

Отзывы:

Похожие инструкции для Lincoln Impinger 1600 Series

Бренды по названию

Популярные бренды