WEJOIN DC24V Скачать руководство пользователя страница 25

Страница: 25 / 27

closing

direction

extended to too much

The LED digital tube
of the slave motor
displays IdLE

The slave motor sensor
plug is not plugged in or
the wire is loose

Check the slave motor sensor
plug

Slave

motor

sensor

failure

Replace the slave motor

LED Prompt: motor
sensor is not detected

The main motor sensor
plug is not plugged in or
the wire is loose

Check the main motor senor plug,
and plug well

Main

motor

sensor

failure

Replace the main motor

The control board is
not powered on

The fuse is blown

Replace the fuse with the same
specification

The power supply has no
out put

Check the power supply or power
circuit

Boom shakes a lot at up
limit position

Opening speed in up
limit

position

relatively large

Reduce the value of 1.5 in regular
menu of the main motor

Opening

deceleration

angle is large

Reduce the value of 1.3/1.5 in
regular menu of the main motor at
the same time

Boom shakes a lot at
down limit position

Closing speed in down
limit

position

relatively large

Reduce the value of 2.5 in regular
menu of the main motor

Closing

deceleration

angle is large

Reduce the value of 2.3/2.5 in
regular menu of the main motor at
the same time

Remote

control

distance is short

The battery voltage of
remote controller is too
low

Replace the batteries

High-voltage wires or
strong electromagnetic
causing

serious

interference near the
barrier gate

Replace the high-power remote
controller

Remote

control The remote controller Contact the manufacturer

Содержание DC24V




























Результаты поиска

Содержание DC24V

Отзывы:

Похожие инструкции для DC24V

Бренды по названию

Популярные бренды

WEJOIN DC24V, Руководство пользователя

Результаты поиска

Содержание DC24V

Отзывы:

Похожие инструкции для DC24V

Бренды по названию

Популярные бренды