manualshive.com logo in svg

Weishaupt W-FM 25, Руководство пользователя

Поделиться
Скачать
Weishaupt W-FM 25 Скачать руководство пользователя страница 5

1 User instructions

This installation and operating manual forms part of the appliance and must be kept

on site.
Observe installation and operating manual of the burner.
This installation and operating manual supplements the following chapters in the in-

stallation and operating manual of the burner:

▪

Technical description and/or Product description

▪

Commissioning and operation and/or Commissioning

▪

Cause and rectification of faults and/or Troubleshooting

▪

Technical data.

The chapter Display and operating modes and operation is replaced completely.

1.1 User guide

1.1.1 Symbols

DANGER

Immediate danger with high risk. 

Non observance can lead to serious injury or death.

WARNING

Danger with medium risk. 

Non observance can lead to environmental damage,

serious injury or death.

CAUTION

Danger with low risk. 

Non observance can cause damage to the equipment

and injury to personnel.

Important information

Requires direct action

Result after an action

Itemisation

Range of values

1.1.2 Target group

These installation and operating instructions are intended for the operator and quali-

fied personnel. They should be observed by all personnel working on the unit.
Work on the unit must only be carried out by personnel who have the relevant training

and instruction.
Persons with limited physical, sensory or mental capabilities may only work on the unit

if they are supervised or have been trained by an authorised person.
Children must not play near or on the unit.

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

1 User instructions

83294002 • 2/2014-11 • La

5-70

Содержание W-FM 25









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды