manualshive.com logo in svg

Weishaupt W-FM 25, Руководство пользователя

Поделиться
Скачать
Weishaupt W-FM 25 Скачать руководство пользователя страница 46

▶

Press [+].

✓

Switch on point stage 2 when running open (P

3

) is displayed.

▶

Press and hold [L/A] and set the same values as for P

2

 using the [–] or [+] key.

▶

Press [G] and [L/A] simultaneously.

✓

Combustion manager changes to operating level (

10

), depending on heat demand

stage 

1

 or stage 

2

 is displayed.

3. Check start behaviour and on/off switch points

▶

Switch off and restart burner.

▶

Check start behaviour.

▶

Check on and off switch point stage 2:

▪

excess air phase prior to switch over must not be too long,

▪

flame must not fail.

▶

If necessary correct ignition position P

0

.

▶

If necessary correct switch on and point P

3

 or switch off point P

2

.

If the existing settings have been changed:

▶

Re-check start behaviour and on and off switch points.

4. Deactivate E-Parameters

Burner must be in Standby (

OFF

).

▶

Press [Enter] and [+] keys simultaneously for approx. 2 seconds.

✓

The parameter level is activated.

▶

Press [+].

▶

Press [Enter] key until parameter 

E

 is displayed.

▶

Set parameter 

E

 to 

OFF

.

✓

E

-Parameters are not shown in the setting level.

▶

Press [Enter] key twice.

✓

Combustion manager returns to the operating level.

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

6 Commissioning

83294002 • 2/2014-11 • La

46-70

Содержание W-FM 25









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды