Weishaupt W-FM 25 Скачать руководство пользователя страница 43

Страница: 43 / 72

▶

Press [+].

✓

is displayed.

▶

Set value

(flame sensor QRB) using [ENTER] and [+] key.

▶

Press [+].

✓

is displayed.

▶

Adopt value

(fan control), if necessary set using [ENTER] and [-] or [+] key.

▶

Press [+].

✓

is displayed.

▶

Adopt value

(no ignition delay), if necessary set using [ENTER] and [-].

▶

Press [+].

✓

Combustion manager changes into the setting level for step points.

▶

Determine the air damper setting for operating points P

, P

and P

from the

sticker for burner setting.

The operating points are preset using these values:

▶

Press [+].

✓

Factory setting operating point P

(Full load) is displayed.

▶

Press and hold [L/A] and set air damper setting using the [–] or [+] key.

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

6 Commissioning

83294002 • 2/2014-11 • La

43-70

Содержание W-FM 25









































































Результаты поиска

Содержание W-FM 25

Отзывы:

Бренды по названию

Популярные бренды

Weishaupt W-FM 25, Руководство пользователя

Результаты поиска

Содержание W-FM 25

Отзывы:

Бренды по названию

Популярные бренды