manualshive.com logo in svg

Weishaupt W-FM 25, Руководство пользователя

Поделиться
Скачать
Weishaupt W-FM 25 Скачать руководство пользователя страница 47

6.4 Dual fuel burner

6.4.1 Adjusting gas side

1. Preset combustion manager

▶

Set fuel selection switch to GAS.

▶

Unplug bridging plug No. 7 on combustion manager.

▶

Switch on voltage supply.

✓

The unprogrammed condition of the combustion manager is indicated by a flashing

display.

The burner goes to lockout.

▶

Press [ENTER] key.

✓

Burner has been reset.

✓

Combustion manager drives to Standby.

▶

Press [G] and [L/A] simultaneously.

✓

Combustion manager changes to access level.

▶

Press [+].

✓

Setting level (parameter 

E0

) is displayed.

▶

Set value 

1

 (dual fuel burners) using [ENTER] and [+] key.

▶

Press [+].

✓

E1

 is displayed.

▶

Adopt value 

0

 (intermittent operation) using [+] key.

✓

E2

 is displayed.

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

6 Commissioning

83294002 • 2/2014-11 • La

47-70

Содержание W-FM 25









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды