Weishaupt W-FM 25 Скачать руководство пользователя страница 38

Страница: 38 / 72

▶

Press [+].

✓

is displayed.

The value of parameter

can not be altered.

▪

= intermittent operation (Standard)

▪

= continuous operation (only if W-FM 21was used previously)

▶

Press [+].

✓

is displayed.

▶

Adopt value

(ionisation electrode), if necessary adjust using [ENTER] and [-] key.

▶

Press [+].

✓

is displayed.

▶

Adopt value

(fan control), if necessary set using [ENTER] and [-] or [+] key.

▶

Press [+].

✓

Combustion manager changes into the setting level for step points.

▶

Determine the air damper setting and fan speed for operating points P

, P

and

from the sticker for burner setting.

The operating points are preset using these values:

▶

Press [+].

✓

Factory setting operating point P

(Full load) is displayed.

▶

Press and hold [L/A] and set air damper setting using the [–] or [+] key.

▶

Press and hold [G] and set fan speed using [–] or [+] key.

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

6 Commissioning

83294002 • 2/2014-11 • La

38-70

Содержание W-FM 25









































































Результаты поиска

Содержание W-FM 25

Отзывы:

Бренды по названию

Популярные бренды

Weishaupt W-FM 25, Руководство пользователя

Результаты поиска

Содержание W-FM 25

Отзывы:

Бренды по названию

Популярные бренды