Weidmuller UR67-PB-12-8DI-8-30K Скачать руководство пользователя страница 44

Страница: 44 / 45

9 LED indicators and troubleshooting

2484950000/00/03.2016

Manual UR67-PROIFBUS

Module

LED

Status

Recommended action

2426390000, 2426380000, 2426400000

Red

: Fieldbus error, no communication

Off

: No error

–

Red

: Check the fieldbus cable and the PLC configuration,

check whether the GSD file is up-to-date

DIA

Red

: Collection error for peripheral errors

Off

: No error message present

–

Red

: Check, on which channel the connected device

causes an error. At least one channel LED must also

shine.

Green

: Sensor-/system supply OK

Red

: Sensor-/system supply < 18 V or > 30 V

Off

: No sensor-/system supply

–

Red

: Check the power supply of the module

Green

: Actuator supply OK

Red

: Actuator supply < 18 V or > 30 V

Off

: No actuator supply

–

Red

: Check the power supply of the module

ACT

Yellow

: Data exchange with PROFIBUS master

Off

: No connection

–

Off

: Check the fieldbus connection

1 … 8 A

Status Channel

Yellow

: Channel A "On"

Red

: Peripheral error (actuator low voltage, sensor or

actuator short circuit)

Off

: Not connected, status „Off“, no error

–

Red

: Check the connected periphery for short circuit,

check the power supply of the peripheral device

1 … 8 B

Status Channel

Yellow

: Channel B „On“

Red

: Peripheral error (actuator low voltage, sensor or

actuator short circuit)

Off

: Not connected, status „Off“, no error

–

Red

: Check the connected periphery for short circuit,

check the power supply of the peripheral device

Содержание UR67-PB-12-8DI-8-30K














































Результаты поиска

Содержание UR67-PB-12-8DI-8-30K

Отзывы:

Похожие инструкции для UR67-PB-12-8DI-8-30K

Бренды по названию

Популярные бренды

Weidmuller UR67-PB-12-8DI-8-30K, Руководство пользователя

Результаты поиска

Содержание UR67-PB-12-8DI-8-30K

Отзывы:

Похожие инструкции для UR67-PB-12-8DI-8-30K

Бренды по названию

Популярные бренды