Weco Cruiser 402 T, Инструкция по эксплуатации

Страница: 24 / 50

Cod.006.0001.1680
24/04/2014 v2.0
ENGLISH
Cruiser 402 T - Cruiser 502 T
Power Pulse 402 T - Power Pulse 502 T
24/50
4.5 PARAMETERS SETTING: (1ST LEVEL)
S2 Press this button to scroll the list of settings to edit.
The acronym relative to the setting to be edited appears on the following displays: D1
The value relative to the selected setting appears on the following displays: D2
E1 Using the encoder, edit the value of the selected setting.
The value is saved automatically.
Press any key (except S2) to save the setting and quit the menu.
Tab. 3 - Parameters of the 1st level menu: MMA mode
ACRONYM PARAMETER MIN DEFAULT MAX
-
WELDING CURRENT
MAXIMUM CURRENT WITH REMOTE CONTROLLER
10 A 10 A 500 A *5
Ho.S. HOT-START 0 % *SYn 100 % *1 *2
Ar.F. ARC FORCE 0 % *SYn 250 % *1 *3
Tab. 4 - Parameters of the 1st level menu: DESEAMING mode
ACRONYM PARAMETER MIN DEFAULT MAX
-
WELDING CURRENT
MAXIMUM CURRENT WITH REMOTE CONTROLLER
10 A 10 A 500 A *5
Tab. 5 - Parameters of the 1st level menu: CONTINUOUS DC TIG mode
ACRONYM PARAMETER MIN DEFAULT MAX
Pr.G. PRE-GAS TIME 0.0 s 0.1 s 10.0 s
St.C. STARTING CURRENT
5 A 50 A 500 A *4 *8
2 % 50 % 200 % *4 *8
Sl.u. SLOPE UP 0.0 s 0.0 s 25.0 s
-
WELDING CURRENT
MAXIMUM CURRENT WITH REMOTE CONTROLLER
5 A 80 A 500 A *5
S.Cu. SECOND CURRENT B-LEVEL 10 % 50 % 200 % *1
Sl.d. DOWN SLOPE 0.0 s 0.0 s 25.0 s *8
F.Cu. FINAL CURRENT
5 A 5 A 500 A *4 *8
5 % 5 % 80 % *4 *8
Po.G. POST GAS TIME 0.0 s 10.0 s 25.0 s
Tab. 6 - Parameters of the 1st level menu: PULSED TIG DC mode
ACRONYM PARAMETER MIN DEFAULT MAX
Pr.G. PRE-GAS TIME 0.0 s 0.1 s 10.0 s
St.C. STARTING CURRENT
5 A 50 A 500 A *4 *8
2 % 50 % 200 % *4 *8
Sl.u. SLOPE UP 0.0 s 0.0 s 25.0 s
-
WELDING CURRENT
MAXIMUM CURRENT WITH REMOTE CONTROLLER
5 A 80 A 500 A *5
S.Cu. SECOND CURRENT B-LEVEL 10 % 50 % 200 % *1
b.Cu. BASE CURRENT 1 % 40 % 200 %
PE.t. PEAK TIME 1 % 50 % 99 %
bA.t. BASE CURRENT 0.1 s 5.0 s 5.0 s
P.Fr. PULSED CURRENT FREQUENCY 0.1 Hz 100 Hz 2.5 kHz
Sl.d. DOWN SLOPE 0.0 s 0.0 s 25.0 s *8
F.Cu. FINAL CURRENT
5 A 5 A 500 A *4 *8
5 % 5 % 80 % *4 *8
Po.G. POST GAS TIME 0.0 s 10.0 s 25.0 s
*1: This parameter is set as a percentage referred to the value of the following parameter:
WELDING CURRENT
*2: The value is limited to 250 A max.
*3: The value is limited to 500 A max.
*4: The value of this parameter can be set as a percentage of the welding current or as an absolute value expressed in Amperes.
*5: This setting is used to adjust both parameters.
*SYN: This code indicates that parameters control is synergic.
The optimal value of this parameter is set automatically by the microprocessor on the basis of the preset welding current value.
When SYN is installed, to display the synergic value press the following button: S5
This value can be displayed but it is not user-adjustable.
*8: The parameter is displayed but it is not used the during welding process when the following setting is present:
MULTI TACK = ON