background image

16

Power Up

 (Cont.)

Rionfuse CF

To fuse a CF fitting, first choose the size:

Use the 

UP/DOWN buttons

 to scroll through the list of available sizes. When you get to the size that 

you want, press the 

START button

 to confirm the selection.

Next, you will be prompted to select the type of heat cycle:

Use the 

UP/DOWN buttons

 to highlight the desired heat cycle. Press the 

START button

 to select 

the desired heat cycle.

NOTE:

 

If this fusion is being performed in an environment where the ambient temperature is below  

 

50°F, please consult Orion Engineering Department at 

910-865-7530 

for pre-heat instructions  

 

before proceeding. All other fusions should be performed using the STANDARD heat cycle.  

 

See page 32 for more information about fusing in low-ambient temperature environments.

Once the heat cycle type has been selected, see page 21 for instructions on completing the fusion.

SELECT SIZE

1.5 in

SELECT TYPE OF CYCLE

 1.  Standard
 2.  Preheat/Warm Up

Always consult with the fitting manufacturer for 

instructions pertaining to when a Preheat Cycle 

should be performed.

Содержание ORION Rionfuser




































Отзывы: