Watts Aerco Benchmark Series Скачать руководство пользователя

Страница: 91 / 146

Benchmark Platinum-Edge: Operation-Service Manual

SECTION 7 – BOILER SEQUENCING TECHNOLOGY

OMM-0137_D • GF-211

•

7/16/2019

Technical Support

•

(800) 526-0288

•

Mon-Fri, 8 am - 5 pm EST Page 91 of 146

7.3.5 Option 5 Remote Setpoint: Direct Wired Header Sensor & 4-

20ma Setpoint Drive

OPTION 5

Instructions: Remote Setpoint, Direct Wired Header Sensor, 4-20ma Setpoint Drive

NOTE:

Both

Header Sensor

and

4-20ma Direct Drive

must be wired. See the

Edge Controller

Manual

(OMM-0139, GF-213) for more information.

Step 1: HEADER SENSOR WIRING – MANAGER Unit

1. On the

Manager

unit, connect the Header Temperature Sensor (P/N

24410

) to the I/O

board terminal strip

, terminals

(

Supply

)

and

(

Supply Header

-).

2. Connect the shield to any

Shield

terminal, such as terminal 3 or 8 on strip

NOTES:

•

The header sensor must be installed between 2 and 10 feet (0.61 and 3.1m)

downstream of the LAST boiler in the plant’s supply water header.

•

Shielded pair 18 - 22 AWG cable is recommended for header sensor wiring. There is no

polarity to be observed. The ground for the shield is at the

Shield

terminal on the I/O

the board. The sensor end of the shield must be left free and ungrounded.

Step 2: DIRECT WIRED 0-20mA or 4-20mA WIRING – MANAGER Unit

1. Connect the 4-20mA or 0-20mA terminals from the Direct Drive source to the I/O Board

strip

, terminals 6

(

Remote Analog In +)

and

(

Remote Analog In –)

on the Manager.

2. Connect the shield to any

Shield

terminal on the I/O Board, such as terminal 3 or 8.

NOTES:

•

Shielded pair 18 - 22 AWG cable is recommended for this connection. Polarity must be

observed.

•

The ground for the shield is at the driver signal source.

Continued on next page

HEADER TEMP SENSOR
(P/N

24410

)

5 Supply Header-

3 Shield

I/O BOARD STRIP J3

4 Supply

Remote
Remote Signal –

8 Shield

I/O BOARD STRIP J3

6 Remote Analog In +

7 Remote Analog In –

Содержание Aerco Benchmark Series



















































































































































Результаты поиска

Содержание Aerco Benchmark Series

Отзывы:

Похожие инструкции для Aerco Benchmark Series

Бренды по названию

Популярные бренды

Watts Aerco Benchmark Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco Benchmark Series

Отзывы:

Похожие инструкции для Aerco Benchmark Series

Бренды по названию

Популярные бренды