Watts Aerco Benchmark Series Скачать руководство пользователя

Страница: 60 / 146

Benchmark Platinum-Edge: Operation-Service Manual

SECTION 5 – SAFETY DEVICE TESTING

OMM-0137_D • GF-211

•

7/16/2019

Technical Support

•

(800) 526-0288

•

Mon-Fri, 8 am - 5 pm EST Page 60 of 146

HIGH Gas Pressure Test Instructions: BMK 3000 – 6000 ONLY

6. Open the

external

gas supply ball valve upstream of the unit.

7. On the Controller, go to:

Main Menu



Diagnostics



Manual

Run

and then enable the

Manual Mode

control.

8. Use the

(Plus) and

–

(Minus) controls to bring the unit up to 100%.

9. Slowly increase the manifold gas supply pressure by turning the Gas Pressure Adjustment

Screw in the Downstream SSOV (Figure 5-2) while reading the CO level on the combustion
analyzer. Adjust the manifold pressure until the CO reading is

approximately 300 ppm

Note the number of turns you make, as you will turn it back to its original position in step 13,
below.

10. Take a reading of the manifold gas pressure. If the manifold pressure is

greater

than the

maximum calculated in step 3, then use the Gas Pressure Adjustment Screw to decrease
the manifold pressure until it is at the maximum allowed.

11. Slowly turn the indicator dial on the High Gas Pressure switch until the unit shuts down due

to a gas pressure fault. This is the setpoint.

12. Press the

RESET

button on the High Gas Pressure switch (see Figure 5-4, below).

13. Readjust the manifold gas supply pressure to what it was before it was increased in step 9.

14. Press the

CLEAR

button on the Edge Controller to clear the fault.

15. Fire the unit back up to insure gas pressure out of the SSOV is set as it was originally.

16. Upon test completion, close the ball valve and remove the manometer fitting from the port,

and then turn the port screw clockwise till the port is closed.

17. For Dual Fuel gas trains, repeat this procedure on the

Propane

gas train, starting with

opening the port on the

Propane

High Gas Pressure Switch, as shown in Figure 5-4b.

Figure 5-4a: HIGH Gas Pressure Test Components – BMK 3000

AIR/FUEL

VALVE

MANUAL SHUT-

OFF VALVE

HIGH Gas

Pressure Port

Install manometer

here for High Gas

Pressure test

LOW GAS
PRESSURE
SWITCH

HIGH GAS

PRESSURE

SWITCH

Alternative

HIGH Gas

Pressure Port

HIGH GAS

BALL VALVE

SSOV

NATURAL
GAS INLET

(P/N 22310 shown)

Содержание Aerco Benchmark Series



















































































































































Результаты поиска

Содержание Aerco Benchmark Series

Отзывы:

Похожие инструкции для Aerco Benchmark Series

Бренды по названию

Популярные бренды

Watts Aerco Benchmark Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Aerco Benchmark Series

Отзывы:

Похожие инструкции для Aerco Benchmark Series

Бренды по названию

Популярные бренды