Wascomat WS3 230 H, Инструкция по эксплуатации

Страница: 24 / 178

Notice Date Page
01201055
INSTRUCTION
HANDBOOK
0102 8
8
8.Technical
characteristics
Heating Gas Electric Steam Thermic fluid
Characteristics Ø cage --------------------------- 770 mm (30.31")--------------------
Cage length ----------------------------- 1500 mm (59") -------------------
Cage volume ----------------------- 668 dm³ (668 l) --------------------
Specific load 1/11 --------------------------- 61 kg (134 lb)-----------------------
(dry linen, ISO 9398-4)
Opening cage doors (L x H) ---------------- 2x600 x 400 mm (23.62x15.74")-----------
Opening drum door (L x H) --------------- 2x616 x 525 mm (24.25x20.66") -----------
Floor area ------------------------ 2 m² (21.53 sq. ft) --------------------
Net weight --------------------------- 940 daN (2073 lb)-----------------
Weight loaded (high level) ---------------------------1589 daN (3504 lb)-----------------
Water, washing, low level xx l xx l xx l xx l
Water, washing, high level xx l xx l xx l xx l
Dynamic stress --------------------- F = 466 daN (1028 lb)-------------------
Transmitted floor load ------------------------ 811 daN (1789 lb)------------------
Spin efficiency ---------------------------------- 350 G ------------------------
Max. unbalance --------------------------- 8 kg (17.65 lb)--------------------
(L) Main switch to connect main cable
(M) Electric cable (section)
4x2.5 mm² 4x35 mm² 4x2.5 mm² 4x2.5 mm²
(N) or (N') Stuffing box for main cable
Supply voltage
-------------------------380 / 415 V 3+E ~ 50/60 Hz------------
Installed electric power 7.8 kW 61.5 kW 7.8 kW 7.8 kW
Installed heating power 40 kW 54 kW - -
Electrical consumption for a normal cycle * 2 kWh/h 23 kWh/h 2 kWh/h 2 kWh/h
Heat loss -------------------3 % of installed heating power--------------
(G) Steam inlet DN 20 (3/4" BSP)
- Maximum supply pressure 600 kPa (87 psi)
- Steam instantaneous flow rate at 600 kPa x kg/h
- Steam consumption for a normal cycle* 24.5 kg/h at 600 kPa (87 psi)
(D) Hot water connection / flow DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(E) Cold hard water connection / flow DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
(F) Cold soft water connection / flow (option) DN 20 (3/4" BSP) - 70 l/min at 250 kPA (36 psi)
Water supply minimum pressure --------------------------- 50 kPa (7.25 psi)------------------
Water supply maximum pressure --------------------------- 300 kPa (43.5 psi)----------------
Water consumption for a normal cycle * 977 l 977 l 977 l 977 l
Water consumption for an ECO cycle ** 782 l 782 l 782 l 782 l
(K) Liquid detergents inlet
(H1 or H3 or H5) Drain connection --------------------------- Ø 75 mm (3")----------------------
(H2 or H4 or H6) Double drain connection --------------------------- Ø 75 mm (3")----------------------
Maximum drain flow rate xx l/min xx l/min xx l/min xx l/min
(I) Waste water collector ------------------------ DN 150 mm (6" BSP)----------------
(3 cm/m (3 %) minimum slope)
(J) Air vent hole ------------------------ Ø 60 mm (2.36 ") ---------------------
(N') Thermic fluid inlet DN 15 (1/2" BSP)
(G) Thermic fluid return DN 15 (1/2" BSP)
- Maximum supply pressure xxx kPa
- Installed calorific power xxx kcal
- Average calorific consumption xxx kcal/h
- Inner volume thermic fluid xx l
Gas inlet DN 20 (3/4" BSP)
Combustion products evacuation Ø 125 mm (5")
Washer extractor type 670 standard
Diagram no. 07100087
* normal cycle : prewash 3 min at 35 °C, drain. 2 min, main wash 4 min at 65 °C, drain 2 min, rinse 2 min, extract. 2 min, rinse 2 min,
extract 2 min, rinse 2 min, extrac. 10 min (cold water supply at 15 °C).
** ECO cycle : normal cycle with rinse 5 l/kg instead of 6 l/kg dry linen.