manualshive.com logo in svg

WÄRTSILÄ 12V46F, Руководство по эксплуатации продукта

Двигатель Wärtsilä 12V46F - мощный и надежный агрегат для морского использования. У нас вы можете бесплатно загрузить руководство по эксплуатации этого двигателя на нашем сайте manualshive.com. Не упустите возможность получить полезную информацию о продукте перед его использованием.

Поделиться
Скачать
background image

6.3.2

Fuel tanks

The fuel oil is first transferred from the bunker tanks to settling tanks for initial separation of
sludge and water. After centrifuging the fuel oil is transferred to day tanks, from which fuel is
supplied to the engines.

6.3.2.1

Settling tank, HFO (1T02) and MDF (1T10)

Separate settling tanks for HFO and MDF are recommended.

To ensure sufficient time for settling (water and sediment separation), the capacity of each
tank should be sufficient for min. 24 hours operation at maximum fuel consumption. The tanks
should be provided with internal baffles to achieve efficient settling and have a sloped bottom
for proper draining. The temperature in HFO settling tanks should be maintained between
50°C and 70°C, which requires heating coils and insulation of the tank. Usually MDF settling
tanks do not need heating or insulation, but the tank temperature should be in the range
20...40°C.

6.3.2.2

Day tank, HFO (1T03) and MDF (1T06)

Two day tanks for HFO are to be provided, each with a capacity sufficient for at least 8 hours
operation at maximum fuel consumption. A separate tank is to be provided for MDF. The
capacity of the MDF tank should ensure fuel supply for 8 hours. Settling tanks may not be
used instead of day tanks.

The day tank must be designed so that accumulation of sludge near the suction pipe is
prevented and the bottom of the tank should be sloped to ensure efficient draining. HFO day
tanks shall be provided with heating coils and insulation. It is recommended that the viscosity
is kept below 140 cSt in the day tanks. Due to risk of wax formation, fuels with a viscosity
lower than 50 cSt at 50°C must be kept at a temperature higher than the viscosity would
require. Continuous separation is nowadays common practice, which means that the HFO
day tank temperature normally remains above 90°C. The temperature in the MDF day tank
should be in the range 20...40°C. The level of the tank must ensure a positive static pressure
on the suction side of the fuel feed pumps.

If black-out starting with MDF from a gravity tank is foreseen, then the tank must be located
at least 15 m above the engine crankshaft.

6.3.2.3

Leak fuel tank, clean fuel (1T04)

Clean leak fuel is drained by gravity from the engine. The fuel should be collected in a separate
clean leak fuel tank, from where it can be pumped to the day tank and reused without
separation. The pipes from the engine to the clean leak fuel tank should be arranged continuosly
sloping. The tank and the pipes must be heated and insulated, unless the installation is designed
for operation on MDF only.

The leak fuel piping should be fully closed to prevent dirt from entering the system.

6.3.2.4

Leak fuel tank, dirty fuel (1T07)

In normal operation no fuel should leak out from the components of the fuel system. In
connection with maintenance, or due to unforeseen leaks, fuel or water may spill in the hot
box of the engine. The spilled liquids are collected and drained by gravity from the engine
through the dirty fuel connection.

Dirty leak fuel shall be led to a sludge tank. The tank and the pipes must be heated and
insulated, unless the installation is designed for operation exclusively on MDF.

Wärtsilä 46F Product Guide - a19 - 1 December 2017

6-9

6. Fuel Oil System

Wärtsilä 46F Product Guide

Содержание 12V46F









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 12V46F

Hacker E10 Manual preview
E10
Бренд: Hacker Страницы: 8
JetCat RX Series Manual preview
RX Series
Бренд: JetCat Страницы: 54
Golen Jeep Six-Cylinder Setup Manual preview
Jeep Six-Cylinder
Бренд: Golen Страницы: 11
Econex AR2 SE Series Installation And Operating Instructions Manual preview
AR2 SE Series
Бренд: Econex Страницы: 14
Ecofly Smart M 160/1 Manual preview
Smart M 160/1
Бренд: Ecofly Страницы: 20
Tanaka TC-47R Illustrated Parts Manual preview
TC-47R
Бренд: Tanaka Страницы: 10
Dynamite Fuse DYN3754 Instruction Manual preview
Fuse DYN3754
Бренд: Dynamite Страницы: 28
Key Automation INT Instructions And Warnings For Installation And Use preview
INT
Бренд: Key Automation Страницы: 50
Siemens Simodrive 611 Installation Manual preview
Simodrive 611
Бренд: Siemens Страницы: 4
Siemens SIMOTICS A-1FV5 Operating Instructions Manual preview
SIMOTICS A-1FV5
Бренд: Siemens Страницы: 66
Siemens SIMOGEAR 2332 Original Mounting And Operating Instructions preview
SIMOGEAR 2332
Бренд: Siemens Страницы: 56
Siemens SIMODRIVE POSMO A Function Manual preview
SIMODRIVE POSMO A
Бренд: Siemens Страницы: 58
Siemens SIMOTICS GP Operating Instructions Manual preview
SIMOTICS GP
Бренд: Siemens Страницы: 100
Siemens Simotics HV C 1NA14544WA600AG0-Z Operating Instructions And Installation Instructions preview
Simotics HV C 1NA14544WA600AG0-Z
Бренд: Siemens Страницы: 112
Siemens SIMOTICS DP 1PC13 Operating Instructions Manual preview
SIMOTICS DP 1PC13
Бренд: Siemens Страницы: 100
Siemens SIMOTICS DP 1PC134 Operating Instructions Manual preview
SIMOTICS DP 1PC134
Бренд: Siemens Страницы: 120
Siemens SIMOTICS HT Series Operating Instructions & Installation Instructions preview
SIMOTICS HT Series
Бренд: Siemens Страницы: 128
Siemens SIMOTICS HV M Operating Instructions Manual preview
SIMOTICS HV M
Бренд: Siemens Страницы: 136

Бренды по названию

Популярные бренды

Загрузить еще бренды