FCC Regulation
This device complies with Part 15 of the FCC Rule. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
§ 15.21 Information to user.
The users manual or instruction manual for an intentional or
unintentional radiator shall caution the user that changes or
modi cations not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment. In cases where the manual is provided only in a form
other than paper, such as on a computer disk or over the Internet, the
information required by this section may be included in the manual in
that alternative form, provided the user can reasonably be expected
to have the capability to access information in that form.
As you read these instructions,
you will see
WARNINGS,
CAUTIONS, NOTICES
and
NOTES
. Each message has a speci c
purpose. WARNINGS are safety messages that indicate a potentially
hazardous situation, which, if not avoided could result in serious
injury or death. CAUTIONS are safety messages that indicate a
potentially hazardous situation which, if not avoided, could result
in minor or moderate injury. A CAUTION may also be used to alert
against unsafe practice. CAUTIONS and WARNINGS identify the
hazard, indicate how to avoid the hazard, and advise of the probable
consequence of not avoiding the hazard. NOTICES are messages to
avoid property damage. NOTES are additional information to help
you complete a procedure.
PLEASE WORK SAFELY!
Warnings and Cautions
Industry Canada
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation
of the device.
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.)
is not more than that necessary for successful communication.
This radio transmitter (identify the device by certi cation number, or
model number if Category II) has been approved by Industry Canada
to operate with the antenna types listed below with the maximum
permissible gain and required antenna impedance for each antenna
type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
WARN INDUSTRIES
5
GENERAL SAFETY PRECAUTIONS
MOVING PARTS ENTANGLEMENT HAZARD
Failure to observe these instructions could lead to
serious injury or death.
General Safety:
•
Always
Know Your Winch. Take time to fully read the
Instructions and/or Operations Guide, and/or Basic Guide
to Winching Techniques, in order to understand your
winch and its operations, found online at
http://www.
warn.com/corporate/literaturerequest.shtml
.
•
Never
exceed winch or winch rope rated capacity. Double
line using a snatch block to reduce winch load.
•
Always
wear heavy leather gloves when handling winch
rope.
•
Never
use winch or winch rope for towing. Shock loads
can damage, overload and break rope.
•
Never
use a winch to secure a load.
•
Never
operate this winch when under the in uence of
drugs, alcohol or medication.
•
Never
operate this winch if you are under 16 years of age.
Installation Safety:
•
Always
choose a mounting location that is suffi ciently
strong to withstand the maximum pulling capacity of your
winch.
•
Always
use class 8.8 metric (grade 5) or better hardware.
•
Never
weld mounting bolts.
•
Always
use factory approved mounting hardware,
components, and accessories.
•
Never
use bolts that are too long.
•
Always
con rm required bolt length to ensure proper
thread engagement.
•
Always
complete the winch installation and hook
attachment before installing the wiring.
•
Always
keep hands clear of winch rope, hook loop, hook
and fairlead opening during installation, operation, and
when spooling in or out.
•
Always
position fairlead with warning readily visible on
top.
•
Always
prestretch rope and respool under load before
use. Tightly wound rope reduces chances of “binding”,
which can damage the rope.
WARNING
MOVING PARTS ENTANGLEMENT HAZARD
Failure to observe these instructions could lead to
serious injury or death.
Winching Safety:
•
Always
inspect winch rope, hook, and slings before
operating winch. Frayed, kinked or damaged winch
rope must be replaced immediately. Damaged
components must be replaced before operation. Protect
parts from damage.
•
Always
remove any element or obstacle that may
interfere with safe operation of the winch.
•
Always
be certain the anchor you select will withstand
the load and the strap or chain will not slip.
•
Always
use supplied hook strap whenever spooling
winch rope in or out, during installation and during
operation.
•
Always
require operators and bystanders to be aware of
vehicle and or load.
•
Always
be aware of stability of vehicle and load during
winching, keep others away. Alert all bystanders of an
unstable condition.
•
Always
unspool as much winch rope as possible when
rigging. Double line or pick distant anchor point.
•
Always
take time to use appropriate rigging techniques
for a winch pull.
•
Never
touch winch rope or hook while someone else is
at the control switch or during winching operation.
•
Never
engage or disengage clutch if winch is under
load, winch rope is in tension or drum is moving.
•
Never
touch winch rope or hook while under tension or
under load.
•
Always
stand clear of winch rope and load and keep
others away while winching.
•
Never
use vehicle to pull load on winch rope. Combined
load or shock load can damage, overload and break
rope.
•
Never
wrap winch rope back onto itself. Use a choker
chain or tree trunk protector on the anchor.
•
Never
use remote when vehicle is not in line of sight of
operator.
•
Never
pair more than one winch and one remote
together at the same time.
WARNING
WARN INDUSTRIES
6
GENERAL SAFETY PRECAUTIONS
92821A4
92821A4
