background image

Wake N Grill 

(Rev 0)

Instruction Manual (Flat Mount)

Congratulations on your purchase of the Wake N Grill. You are just a few steps away from making a great day on the 

water even better!  

This Wake N Grill kit is designed to provide years of service and satisfaction with the proper care and installation.

Please read these instructions carefully. If, at any time, you have a question about the installation or setup, please 

review the “How To” section at www.wakengrill.com/how-to/ .  If you like talking to a real person, we are here to help.  

Just give us a call at 480-686-3130 for technical assistance. 

After reviewing these instructions, if you feel uncomfortable performing the installation, please contact your local 

dealer.  

*****Important Safety Precautions*****

Please Read

This Wake N Grill is designed to be used while the boat is moored. At no time should the Wake N Grill be used or deployed while the 

vessel is underway. Do not trailer boat while Wake N Grill is deployed.

● Do not allow passengers to hang on or pull on the mid arm support, grill mounting plate, umbrella support, or cutting board 

platform.

● Ensure all bolts and hardware are tightened before each use.

● Do not use if hardware is missing or broken or if the components show any type of stress (cracks, broken welds, etc).

● Ensure all pull pins and twist locks are properly tightened, secured, or seated before each use.

● Do not use umbrella in windy or breezy conditions.

● Do not use Wake N Grill as a tow point.

● Always store propane tanks in accordance with local marine laws and regulations.

● Failure to adhere to these safety warnings and guidelines will void warranty and may cause personal injury.

Wake N Grill

134 E. Broadway Rd. #101

Mesa, AZ  85210

(480) 686-3130

[email protected]

wakengrill.com

Содержание Wake N Grill Flat Mount



















Отзывы: