WAGO 761-217 Скачать руководство пользователя страница 31

Страница: 31 / 138

WAGO-TO-PASS® 761

Device Description

761-217 Telecontrol Module Compact, 8 AI, Web, MODBUS485

Manual

Version 1.0.0

Table 13: MODBUS cable assignment

TO-PASS

Telecontrol Module

MODBUS

Communication Partner

Pin

Description

Pin

Description

GND

MODBUS GND

MODBUS D1 (B)



MODBUS D1 (B)

MODBUS D0 (A)



MODBUS D0 (A)

Figure 11: MODBUS communication diagram

Observe MODBUS pin assignment for communication partner!

The MODBUS pin assignment for the communication partner may differ, based
on the device/manufacturer.
Observe the manufacturer's device description!

MODBUS Line terminator

The MODBUS specification requires a line terminator at both ends of an RS-485
bus.
If the

TO-PASS

telecontrol module is operated at one end of the line, the

terminator must be added (e.g., directly in the D-Sub plug-in connector, or at the
bus terminals of interface module 289-966).
According to the specification, a 150

Ω resistor (0.5 W) or a 1nF capacitor (at

least 10 V) and a 120

Ω resistor (0.25 W) connected in series can be used for this.

If the

TO-PASS

telecontrol module is operated outside the bus (not at the end),

the branch cable must be kept as short as possible.

BIAS Network

Some RS-485 drivers require a BIAS network to ensure a constant status when
there is no transmission (active transmitter) on the bus.
The

TO-PASS

telecontrol module (as the MODBUS master) is equipped with a

BIAS network with two 470

Ω resistors (at GND and +5 V).

Содержание 761-217











































































































































Результаты поиска

Содержание 761-217

Отзывы:

Похожие инструкции для 761-217

Бренды по названию

Популярные бренды

WAGO 761-217, Руководство пользователя

Результаты поиска

Содержание 761-217

Отзывы:

Похожие инструкции для 761-217

Бренды по названию

Популярные бренды