WAGO 753-482 Скачать руководство пользователя

Страница: 6 / 102

Notes about this Documentation

WAGO I/O System 750

753-482 2AI 4-20mA 12 Bit S.E. HART

Manual

Version 1.2.0

Notes about this Documentation

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation

is included, if necessary.

1.1

Validity of this Documentation

This documentation is only applicable to the I/O module 753-482

(2AI 4-20mA 12 Bit S.E. HART).

The I/O module 753-482 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus coupler or

controller.

Consider power layout of the WAGO I/O System 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler or controller, which can be downloaded at

www.wago.com

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

1.2

Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Содержание 753-482







































































































Результаты поиска

Содержание 753-482

Отзывы:

Похожие инструкции для 753-482

Бренды по названию

Популярные бренды

WAGO 753-482, Руководство пользователя

Результаты поиска

Содержание 753-482

Отзывы:

Похожие инструкции для 753-482

Бренды по названию

Популярные бренды