WAGO 753-482 страница 13 Скачать руководство пользователя

Страница: 13 / 102

WAGO I/O System 750

Important Notes 13

753-482 2AI 4-20mA 12 Bit S.E. HART

Manual

Version 1.2.0

2.2

Safety Advice (Precautions)

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Install device in only one suitable enclosure!

The device is an open system. Install the device in a suitable enclosure. This

enclosure must:

• Guarantee that the max. permissible degree of pollution is not exceeded.

• Offer adequate protection against contact.

• Prevent fire from spreading outside of the enclosure.

• Offer adequate protection against UV irradiation.

• Guarantee mechanical stability

•

Restrict access to authorized personnel and may only be opened with tools

Ensure disconnect and overcurrent protection!

The device is intended for installation in automation technology systems.

Disconnect protection is not integrated. Connected systems must be protected by

a fuse.

Provide suitable disconnect and overcurrent protection on the system side!

Ensure a standard connection!

To minimize any hazardous situations resulting in personal injury or to avoid

failures in your system, the data and power supply lines shall be installed

according to standards, with careful attention given to ensuring the correct

terminal assignment. Always adhere to the EMC directives applicable to your

application.

Содержание 753-482







































































































Результаты поиска

Содержание 753-482

Отзывы:

Похожие инструкции для 753-482

Бренды по названию

Популярные бренды

WAGO 753-482, Руководство пользователя

Результаты поиска

Содержание 753-482

Отзывы:

Похожие инструкции для 753-482

Бренды по названию

Популярные бренды