WAGO 753-482 Скачать руководство пользователя страница 52

Страница: 52 / 102

52 Operating Modes

WAGO I/O System 750

753-482 2AI 4-20mA 12 Bit S.E. HART

Manual

Version 1.2.0

Operating Modes

The HART I/O module can be used with various operating modes depending on

connection and parameterization.

Table 29: Overview of Operating Modes

Operating Mode

On Fieldbus

Coupler/Controller

Use

2 AI + 6 bytes mailbox

(Default)

All compatible Fieldbus

couplers/controllers

75x-xxx

1) With

“WagoLibHART_0x.lib”

PLC library

750-841

ETHERNET TCP/IP

Fieldbus controller

2) With ModbusTCP/HART

Gateway 759-359

2 AI + 1 HART variable

per Channel

PROFIBUS DP/V1

Fieldbus coupler

750-333 or Fieldbus

controller 750-833

3) With HART dynamic

variables

2 AI + 2 HART variables

per Channel
2 AI + 3 HART variables

per Channel
2 AI + 4 HART variables

per Channel
2 AI + acyclic PROFIBUS

services

4) With PROFIBUS/HART

Gateway 759-360

see table “Compatibility List”

In the as-supplied state, the HART I/O module is configured in the default

operating mode as a 2-channel analog input module for 4 mA … 20 mA signals

with HART functionality. In this default operating mode the I/O module can be

connected to all WAGO couplers and controllers listed in the table “Compatibility

List”. In this case, HART communication is enabled by a 6-byte mailbox, which is

incorporated with the analog values in the cyclic process image.

In addition, five further operating modes can be set up specially for connecting to

the PROFIBUS DP/V1 Fieldbus Coupler 750-333 or Fieldbus Controller 750-833.

The section “Description of Operation” following the section on parameterization

and a short introduction to the FDT/DTM concept and HART via PROFIBUS,

describes the individual operating modes in the appropriate applications in more

detail together with a description of the communications process and brief

commissioning instructions in each case.

8.1

Setting the Operating Mode Parameters

Depending on the fieldbus used, the HART I/O module can either be

parameterized using the “759-302 WAGO-I/O-

CHECK

” commissioning tool for

WAGO-I/O-SYSTEM 750 or, for PROFIBUS, using the GSD files (device master

data) for PROFIBUS with installation program / Series 750, 752 and 755 (Item

No.: 750-910).

Содержание 753-482







































































































Результаты поиска

Содержание 753-482

Отзывы:

Бренды по названию

Популярные бренды

WAGO 753-482, Руководство пользователя

Результаты поиска

Содержание 753-482

Отзывы:

Бренды по названию

Популярные бренды