WAGO 753-482 Скачать руководство пользователя

Страница: 30 / 102

30 Process Image

WAGO I/O System 750

753-482 2AI 4-20mA 12 Bit S.E. HART

Manual

Version 1.2.0

Process Image

The HART I/O Module provides the fieldbus coupler/controller with a different

amount of process data depending on the operating mode set.

Some fieldbus systems process status information on the input channel with the

help of a status byte.

This status byte can be displayed using the WAGO-I/O-

CHECK

commissioning

tool but processing by the coupler/controller is optional; i.e., access to or

evaluation of the status information depends on the respective fieldbus system.

Mapping of the Process Image in the Fieldbus System!

Mapping the process data of some I/O modules (or their variations) into the

process image is specific to the fieldbus coupler/controller used. This information,

as well as the specific configuration for relevant control/status bytes is located in

the section “Fieldbus-Specific Configuration of Process Data.” This section

describes the process image of the particular coupler/controller.

For pure 4 mA … 20 mA analog values the HART module transmits 16-bit

measured values and optionally 8 status bits on each channel.

The digitalized measured value is transmitted to the process image of the

coupler/controller in a data word (16 bits) as an input byte 0 (low) and input byte

1 (high).

This value is mapped with a resolution of 13 bits on Bit B2 ... B14.

Status information, which can be evaluated in the event of a fault, is contained in

the two least significant bits (B0 and B1). If the measurement is above the

measuring range, Bit B0 is set = 1, and if the measurement is below the

measuring range or if a wire breaks, Bit B0 and B1 are set = 1.

The input voltage range for the measured values of 4 mA to 20 mA is scaled to

the numerical range from 0x0000 to 0x7FFD.

Содержание 753-482







































































































Результаты поиска

Содержание 753-482

Отзывы:

Похожие инструкции для 753-482

Бренды по названию

Популярные бренды

WAGO 753-482, Руководство пользователя

Результаты поиска

Содержание 753-482

Отзывы:

Похожие инструкции для 753-482

Бренды по названию

Популярные бренды