WAGNER Plast Coat 430, Руководство по эксплуатации

Страница: 46 / 116

46
Plast Coat 430
GB
8
SHUTTING DOWN AND CLEANING
Do not clean the motor and control unit of
the mortar spraying machine moistly. And
certainly do not spray down the unit with
high-pressure cleaners or high-pressure
steam cleaners. Danger of short-circuits
caused by water ingressing.
8.1
CLEANING THE MORTAR HOSE
t 1VNQUIFQBJOUCVDLFUFNQUZPSSFQMBDFJUCZBOFNQUZWFT -
sel/bucket.
Important: Do not let the mortar spraying
machine run dry. Switch the device off im-
mediately if no more material comes out of
the tip or if the spray line becomes irregu-
lar. Possible reasons for the problem and
how to correct it can be found in the chap-
ter called „Eliminating faults“.
8.2
CLEANING THE DEVICE AND REPLACING THE
STATOR
t $MFBONPSUBSTQSBZJOHNBDIJOF
To do so, pump graphite pump sliding means or water mixed
with dishwashing liquid through the pump.
7.1
SPRAYING TECHNIQUE
8IJMFTQSBZJOHIPMEUIFTQSBZMBODFBUBVOJGPSNEJTUBODFPG
oDNGSPNUIFPCKFDU0UIFSXJTFUIFTQSBZQBUUFSOXJMM
be uneven.
5IFTQSBZQBUUFSOEFQFOETPOUIFDPBUJOHNBUFSJBMWJTDPTJUZ
UJQTJ[FDPOWFZDBQBDJUZBOEBNPVOUPGBUPNJ[JOHBJS
Examples:
Fine texture
–> large amount of atomizing air
Rough texture –> small amount of atomizing air
Higher convey capacity –> larger amount of atomizing air
Test the desired texture on a test surface.
5IFMBUFSBMMJNJUPGUIFTQSBZKFUTIPVMEOPUCFUPPTIBSQ5IF
EJTUBODFCFUXFFOUIFTQSBZMBODFBOEUIFPCKFDUTIPVMEUIFSF
-
GPSFCFTFMFDUFEDPSSFTQPOEJOHMZ
5IFTQSBZFEHFTIPVMECFHSBEVBMJOPSEFSUPGBDJMJUBUFPWFS
-
lapping of the next coat.
*GUIFTQSBZMBODFJTNPWFEQBSBMMFMBOEBUBOBOHMFPG¡UP
the surface to be coated, the paint mist is minimized.
Note:
Grains and pigments with a sharp edge result in a high rate of
wear of the pump, mortar hose, material tap and tip.
When using the mortar hose while working
POTDBòPMEJOHJUJTCFTUUPBMXBZTHVJEFUIF
hose along the outside of the scaffolding.
7
GENERAL INFORMATION ABOUT
THE APPLICATION TECHNIQUE
GENERAL INFORMATION ABOUT THE APPLICATION TECHNIQUE
t 4XJUDIPòNPSUBSTQSBZJOHNBDIJOFBOEDPNQSFTTPS
t $MPTFNBUFSJBMUBQPOTQSBZMBODF
t 3FNPWFUIFUFYUVSFUJQGSPNUIFTQSBZMBODFBOEDMFBOJU
t 4VCNFSHF TVDUJPOUVCFJOBCVDLFUGVMMPGXBUFSBOEIPME
TQSBZMBODFBCPWFNBUFSJBMDPOUBJOFS
t 4FUEFMJWFSZWPMVNFDPOUSPMMFSUPvi
t *GVTJOHBVUPNBUJDMBODFPQFONBUFSJBMUBQPOTQSBZMBODFJG
using pneumatic lance, set selector switch to “F”.
t 1VNQNBUFSJBMPVUPGIPTFJOUPDPOUBJOFSVOUJMUIFNBUFSJBM
exiting the hose is just a thin liquid.
t *GVTJOHBVUPNBUJDMBODFDMPTFNBUFSJBMUBQPOTQSBZMBODFJG
using pneumatic lance, set selector switch to “A”.
The mortar hose must be pressureless.
If necessary, set the selector switch briefly
to “R” (reverse).
Watch the manometer ––> 0 bar.
Wear safety goggles.
t %FDPVQMFNPSUBSIPTFGSPNQVNQVOJU
t %FDPVQMFTQSBZMBODFGSPNNPSUBSIPTF
t *OTFSUDMFBOJOHCBMMJOUPNPSUBSIPTFBOESFDPOOFDUNPSUBS
hose
t 4FUTFMFDUPSTXJUDIUPi'w
t "GUFS B GFX TFDPOET UIF DMFBOJOH CBMM JT FNJUUFE GSPN UIF
TQSBZMBODF
t %FQFOEJOH PO UIF QSPDFTTFE DPBUJOH NBUFSJBM SFQFBU UIF
cleaning process 3 – 4 times.
The mortar hose must be pressureless.
If necessary, set the selector switch briefly
to “R” (reverse).
Watch the manometer ––> 0 bar.
Wear safety goggles.
t 4FUTFMFDUPSTXJUDIUPi"w
t %FDPVQMFNPSUBSIPTFGSPNQVNQVOJU
A further cleaning option is to use the clean-
JOHBEBQUFS BDDFTTPSZ
This cleaning adapter can be connected to a
XBUFSIPTFPSBUBQCZNFBOTPGUIFDMBXDPV -
pling.
Insert cleaning ball into the mortar hose. Cou-
ple the mortar hose to the cleaning adapter
and rinse through with water.