WAGNER Plast Coat 430, Руководство по эксплуатации

Страница: 41 / 116

41
Plast Coat 430
GB
6
COMMISSIONING
6.1
INSTALLATION LOCATION
5IFNPSUBSTQSBZJOHNBDIJOFBOEUIFCVDLFUGSPNXIJDIUIF
material to be processed is to be pumped have to be set up on
an even and firm underground. This ensures that the machine
BOECVDLFUDBOOPUTMJEFBXBZPSGBMMPWFS
6.2
INITIAL STARTING-UP
6.2.1
SCOPE OF SUPPLY
5IFNBDIJOFJTTVQQMJFECZUIFNBOVGBDUVSFSJOUIFGPMMPXJOH
individual components:
t $PNQMFUFCBTJDNBDIJOFDPNQSJTJOHESJWFVOJUDPOUSPMVOJU
and transport frame with wheels
t Pump unit complete
t 5PPM4QFDJBMLFZ
t
Hose package
t 4QSBZMBODF
t
Pump sliding means
6.2.2
ASSEMBLY
1VMMTBGFUZQJO UPSFBSUPSFMFBTFMPDL1VMM1$VQCZJUT
frame (2) until the machine engages in the top position.
4QSBZSPUPS XJUIBTVJUBCMFQVNQMVCSJDBOU PSEFSOP
824).
.PWFTFMFDUPSTXJUDI UPi"wBOETFUEFMJWFSZWPMVNFDPO -
troller (5) to „0“.
$POOFDUNBJOTQMVHUPNBJOTQPXFSTVQQMZ
COMMISSIONING
t #FGPSFDPOOFDUJOHUIFVOJUUPUIFNBJOTTVQQMZFOTVSFUIBU
the line voltage matches that specified on the rating plate.
Min. wire cross-section 3 x 1.5 mm 2 . Unroll the
FYUFOTJPO DBCMF DPNQMFUFMZ &OTVSF UIBU UIF
coupling pieces and plugs are free of dam-
age.
-BZUIFEFWJDFTVQQMZDBCMFTPUIBUUIFSFJTOP
danger of stumbling.
Protect against damage, for example against
being driven over.
6.1.1
CONNECTION TO MAINS POWER SUPPLY/
EXTENSION CABLE
Connection to the mains network only via a special feed-
ing point, for example via a distribution board for con-
struction sites, with residual current protective device
with INF
≤
30 mA.
The operation light (6) shows operational readiness.
The red indicator light (7) flashes during the function check
for about 30 seconds.
Fold locking pins (8) up towards the magnet holders in the
IBOEMFUPQSFWFOUUIFNCFJOHUXJTUFEEVSJOHBTTFNCMZ
Only the person controlling the machine
may assemble the pump unit.
Never operate mortar spraying machine
with an exposed rotor.
Do not reach into the rotor when it is
moving. Risk of crushing.
Caution if you have long hair. Only wear
close-fitting clothes at work.
Slide pump unit (9) over rotor (3) from below and press up-
wards.
4FUEFMJWFSZWPMVNFDPOUSPMMFS UPPS
Set selector switch (4) to “F” to switch on pump. The pump unit
JTBVUPNBUJDBMMZESBXOVQCZUIFSPUPS
As soon as the pump unit is in its end position, fold the two
locking pins (8) down and use nuts to fix the pump unit.
*GOFDFTTBSZSPUBUFQVNQVOJU CZIBOEUP
move locking pins 8) into end position.
Set selector switch (4) to “A” to switch off pump.
Disconnect mains plug.
After assembling the pump unit, secure the
union nut (10) on the pump unit, using the
TQFDJBMLFZUPEPTP
A
F R
POWER
ERROR
4
6
2
1
4
3
A
F R
POWER
ERROR
5
8
9
10
7