WAGNER Plast Coat 430, Руководство по эксплуатации

Страница: 37 / 116

37
Plast Coat 430
GB
4.1
OPERATING ELEMENTS AND DISPLAYS ON
DEVICE
1 %FMJWFSZWPMVNFDPOUSPMMFS 0-10
2 Selector switch for operating mode
3 Indicator light (Error)
4 Operating light (Power)
5 EMERGENCY STOP switch
5IF EFMJWFSZ WPMVNF DPOUSPMMFS Fig. 3, 1) is used to regulate
UIFDPOWFZDBQBDJUZGSPNTNPPUIMZ
5IFSFNPUFDPOUSPM BWBJMBCMFTFQBSBUFMZBSU
OPDBOCFVTFEUPDPOWFOJFOUMZ
DPOUSPMUIFQVNQATEFMJWFSZWPMVNFGSPNUIF
TQSBZMBODF
The selector switch (Fig. 3, 2) offers the following modes:
A
R F
“A” position = automatic
Basic setting for control with an automatic
TQSBZMBODFQOFVNBUJDTQSBZMBODFPSSF -
mote control
A
R F
“F” position = manual activation
4XJUDIFTPOUIFNPSUBSTQSBZJOHNBDIJOF
This setting is required for:
t TVDUJPOVOJUBTTFNCMZ
When using the pneumatic lance, this set-
ting is also needed for:
t QSFSJOTJOH UIF NPSUBS IPTF UP JNQSPWF
UIFNBUFSJBMATBCJMJUZUPTMJEF
t DMFBOJOH
OVERVIEW
A
R F
“R” position = reverse gear (must be held in
this position).
This setting is required for:
t SFMJFWJOHQSFTTVSFPOUIFNPSUBSIPTF
t TVDUJPOVOJUEJTBTTFNCMZ
Detailed explanation of selector switch use:
If the selector switch is in the “A” position, the PC430 can be
switched on and off with the material shut-off on the auto-
NBUJDPSQOFVNBUJDTQSBZMBODF
*GUIFSFJTOPTQSBZMBODFöUUFE FHBTTFNCMZEJTBTTFNCMZPG
suction unit), the machine is switched on using the “F” switch
position and off using the “A” position.
4JODF UIF BJS TVQQMZ UISPVHI UIF DPNQSFTTPS OFFET UP CF
switched off to clean the mortar hose, the pneumatic lance
is not controlled using the material shut-off. In this case, the
machine must therefore also be switched on using the “F” po-
sition.
Important: control via the selector switch and
NBUFSJBMTIVUPòBSFUSFBUFEFRVBMMZ
The machine can be switched from the “A” po-
sition (control using material shut-off ) to “F” at
BOZUJNF
8FXPVMEUIFSFGPSFSFDPNNFOEUIBUPOMZPOF
person operate the machine.
The operating light (green, Fig. 3, 4) indicates that the machine
JTFOFSHJTFEBOESFBEZ
When the mains plug is connected the PC 430 carries out a
function check. While this is going on the indicator light (red,
öHøBTIFT*GFWFSZUIJOHJTJOXPSLJOHPSEFSUIFøBTIJOH
stops after about 30 seconds. If the indicator light lights up
during operation, this indicates that there is a malfunction. For
detailed information about this kind of fault, refer to the „Rec-
tification of faults“ section on page 49.
If the selector switch is in the “F” position when
the mains plug is plugged in, the machine will not
switch on.
#SJFøZNPWFTFMFDUPSTXJUDIUPi"wBOEUIFOCBDL
to “F” to switch on the machine.
EMERGENCY STOP switch
When the EMERGENCY STOP switch is pressed, the PC 430 is
TXJUDIFEPòJNNFEJBUFMZ
Turn the EMERGENCY STOP switch in order to release it again.
The machine remains switched off after release. To switch it on
BHBJOUIFTFMFDUPSTXJUDINVTUCFCSJFøZTFUUPi"wBOEUIFO
to “F”.
2
A
F R
POWER
ERROR
1
1
4
3
5