Wabtec Ricon K Series Скачать руководство пользователя страница 41

Страница: 41 / 79

3 - 8

MAINTENANCE

SEPTEMBER 2010

32DSKE02.B.1

S/K-SERIES EXPORT USE SERVICE MANUAL

FIGURE 3-8: PIN WITH PIN ALIGNMENT TOOL

Replace and install rear spring.

Refer to

Figures 3-9

. Install a 51mm (2 in.) extension pin through parallel arm and rear spring.

FIGURE 3-9: 2-INCH EXTENSION

FIGURE 3-10: PLACE REAR SPRING

Refer to

Figure 3-10.

Use appropriate tool to use as leverage to pull back tine of bent rear spring and

place into baseplate tower.

Replace 51mm (2-Inch) extension with existing pin.

Reinstall screw and lock washer.

Repeat removal and installation for opposite parallel arm.

HYDRAULIC CYLINDER. GLAND NUT AND PISTON REPLACEMENT

Lower lift to ground level.

NOTE

: Lift must be lowered as far as possible to avoid personal injury and oil spillage when hydraulic components

are dismantled.

Fully open manual release valve.

NOTE

: Important for allowing easy removal/insertion of ram into cylinder.

Install hydraulic breather tube if available.

NOTE

: The hydraulic breather tube may help in avoiding oil overflow from filler neck when reinstalling ram. An as-

sistant may be required to check oil level in filler neck as ram is reinserted, if breather tube is not available.

Loosen both hydraulic button head screws with 5mm (3/16 in.) hex wrench to loosen pin.

Remove and retain cap screw with 4mm (5/32 in.) hex wrench.

Drive rear pin out and retain. Use pin driver, pin is driven towards bushing side.

Drive front pin out and retain.

NOTE

: Hydraulic cylinder may be left in baseplate “U” tower for this and proceeding operations.

k. Refer

Figure 3-11

. Unscrew gland nut.

l. Refer

Figure 3-11

. Pull shaft out.

Содержание Ricon K Series
















































































Результаты поиска

Содержание Ricon K Series

Отзывы:

Бренды по названию

Популярные бренды

Wabtec Ricon K Series, Руководство по обслуживанию

Результаты поиска

Содержание Ricon K Series

Отзывы:

Бренды по названию

Популярные бренды