manualshive.com logo in svg

Wabtec Ricon K Series, Руководство по обслуживанию

Поделиться
Скачать
Wabtec Ricon K Series Скачать руководство пользователя страница 25

 

 

2 - 12

INSTALLATION 

SEPTEMBER 2010 

32DSKE02.B.1 

S/K-SERIES SERVICE MANUAL 

C. FINAL 

ADJUSTMENTS 

1. 

LIMIT SWITCH ADJUSTMENT 

Refer to

 

Figures 2-15 and 2-16 

with the following procedure. 

NOTE: 

To avoid operational “dead-spots”, adjust DEPLOY CUTOFF SWITCH before UP CUTOFF SWITCH. 

NOTE: 

When loosening adjustment screws, apply enough pressure to screw to move block instead of screw.  
(The block might stick if insufficient pressure is applied to screw.) 

RSM0003301

UP CUTOFF SWITCH

CAM

STOW STATUS
ACTUATOR

LOWER CAM
LOBE

DEPLOY CUTOFF SWITCH

UP CUTOFF

ADJUSTMENT SCREW

STOW STATUS SWITCH

DEPLOY CUTOFF

ADJUSTMENT SCREW

 

FIGURE 2-15:  LIMIT SWITCH ADJUSTMENT DIAGRAM 

a.  Fully DEPLOY platform. 
b.  Adjust UP CUTOFF ADJUSTMENT SCREW and DEPLOY CUTOFF ADJUSTMENT SCREW 6-8 turns

 

counterclockwise

 (CCW) and then push screws FORWARD. 

c.  Cycle platform to STOW then DEPLOY. 
d.  When in DEPLOY position, platform should stop at an angle and NOT even with vehicle floor.  If not, turn 

DEPLOY CUTOFF ADJUSTMENT SCREW an additional 2-3 turns 

counterclockwise 

(CCW), push screw 

forward, STOW then DEPLOY platform, then repeat this step. 

e.  Cycle platform to UP position.

 

f. 

When in UP position, platform should stop short of vehicle floor level.  If not, turn UP CUTOFF 
ADJUSTMENT SCREW an additional 2-3 turns 

counterclockwise 

(CCW), push screw forward, cycle plat-

form DOWN then UP, then repeat this step. 

g.  Cycle platform to STOW then DEPLOY. 
h.  Push and hold control pendant DEPLOY switch.  Slowly turn DEPLOY CUTOFF ADJUSTMENT SCREW 

clockwise

 (CW) until platform “jogs” down to vehicle floor level.  Make sure that clearance between knuckle 

actuator saddle and parallel arm is 3mm (1/8 in.) minimum (distance may be 13mm (1/2 in.) maximum and 
unequal from left or right arm), stop turning screw and release DEPLOY switch. 

i. 

Position platform DOWN to ground level then UP until it stops. 

j. 

Push and hold control pendant UP switch.  Slowly turn UP CUTOFF ADJUSTMENT SCREW 

clockwise

 

(CW) until platform “jogs” up to vehicle floor level.  Make sure that clearance between knuckle actuator 
saddle and parallel arm is 

3mm (1/8 in.)

 minimum (distance may be 

13mm (1/2 in.)

 maximum and unequal 

from left or right arm), stop turning screw and release UP switch. 

NOTE: 

If lift does not operate after 1-2 full turns of adjustment screw, cycle platform UP and DOWN (The UP 
CUTOFF SWITCH is less sensitive than DEPLOY CUTOFF SWITCH.) 

 

Содержание Ricon K Series
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды