manualshive.com logo in svg

Wabtec Ricon K Series, Руководство по обслуживанию

Поделиться
Скачать
Wabtec Ricon K Series Скачать руководство пользователя страница 24

 

 

2 - 11

32DSKE02.B.1 

INSTALLATION

SEPTEMEBER 2010 

S/K-SERIES EXPORT USE SERVICE MANUAL 

5. 

INSTALLATION OF INTERLOCK DEVICE 

An interlock device can be installed to prevent operation of the lift or vehicle when it is not safe to do so.  

The inter-

lock supplied by the installing Ricon dealer is not a Ricon product.

 

If interlock option is installed, the S and K-Series lifts provides an electrical interlock signal to the vehicle that pre-
vents movement of the vehicle unless the platform is fully stowed.  The interlock control also supplies power to the 
lift only when the vehicle parking brake is set and the transmission is in PARK. 

Some interlock devices lock vehicle transmission in PARK (or neutral) when lift is deployed, or do not allow lift to be 
deployed unless vehicle transmission is in PARK (or neutral) and emergency brake is set.  Other devices will stall 
vehicle engine if lift is deployed and emergency brake is released or transmission is shifted from PARK (or neutral).  
There may be other types of interlock devices that disable lift or vehicle to prevent unsafe lift operation. 

Ricon is not aware of all available interlock products.  For this reason it is very important that interlock products be 
properly installed so that they do not interfere with safe operation or create any other hazards. 

NOTE: 

A 30 amp circuit breaker is located within the lift as a circuit protection device.  The circuit interface used by 
the installer must be capable of carrying an additional 30 amps of continuous current. 

The installer must verify that none of the original equipment circuit breakers, fuses, or solenoids are bypassed, re-
moved, or altered.  Be sure that no wires are left frayed or hanging loose after installation of an interlock device.  If 
you have any questions about proper installation of interlock devices, please contact our Product Support Depart-
ment. 

           WARNING 

DO NOT OPERATE LIFT UNLESS YOU ARE CERTAIN THAT THE 
INTEGRITY OF LIFT ELECTRICAL CIRCUITS HAS BEEN MAINTAINED. 

 

               CAUTION 

Wiring attached directly to the positive battery terminal is not protected against short circuits 
and must be kept to a length of 305mm (12 in.) or less.  The wiring must be routed in a manner 
that prevents pinching or abrasion by vehicle parts.  The power source wire for the interlock cir-
cuit must be connected to a protected supply such as a dedicated accessory on an existing 
fuse panel. 

Содержание Ricon K Series
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды