manualshive.com logo in svg

Wabtec Ricon K Series, Руководство по обслуживанию

Поделиться
Скачать
Wabtec Ricon K Series Скачать руководство пользователя страница 14

 

 

2 - 1

32DSKE02.B.1 

INSTALLATION

SEPTEMEBER 2010 

S/K-SERIES EXPORT USE SERVICE MANUAL 

II. INSTALLATION 

his chapter contains instructions for installing the RICON S-Series™ and K-Series™ Export Use wheelchair lift 
into most private use vehicles, although custom installations are also possible in other types of vehicles.  Due to 
the wide range of lift applications, specific information for every possible application is not available.  The follow-

ing general procedures will apply to most installations.  Contact Ricon Product Support for instruction concerning instal-
lations not covered.  To install lift, refer to following sections and perform procedures carefully and in the order that they 
are presented.  Be certain that installation instructions are followed exactly and do not eliminate any steps or modify 
product. 

NOTE: 

Please review carefully the installation instructions (32ii427e) that are supplied with this lift before beginning the 
following procedures.  Where these procedures conflict, the installation instructions take precedence. 

A. GENERAL 

MECHANICAL 

INSTALLATION 

1. LIFT 

LOCATION 

The installation surface must be flat and level.  It is recommended that lift be installed on a 13mm (1/2 in.), mini-
mum, high-grade plywood sub-floor.  However, this additional installation height may not be acceptable in cases 
where overhead clearance is limited. 

Refer to Figure

 2-1.

 

NOTE: 

Check for proper travel clearance through doorway.  

a.  With doors fully open, place/position lift in vehicle doorway as close as possible to door, with lift's baseplate 

assembly parallel to side of vehicle. 

b.  Allow a distance of 19mm (3/4 in.), if possible, between door and the part of lift closest to it.  Adjust lift left 

and right-side locations to accommodate subframe members. 

c.  Verify proper clearance of door frame, passenger seats, and outer edge of vehicle floor and possible inter-

ference with wires, fluid lines, subframe members, etc. 

2. VEHICLE 

STRUCTURAL 

REQUIREMENTS 

The following figures and text provide installation guidelines for the RICON S-Series and K-Series Export Use 
wheelchair lift into most vehicles. 

a. 

VEHICLE DOOR OPENING DIMENSIONAL REQUIREMENTS 

in millimeters and [inches].

 

MODEL 

A

  (Width) 

B

  (Height) 

C

  (Floor-To-Ground) 

S1231 

1029 [40.5] 

1118 [44.0] 

787 [31.0] 

S2005 

1080 [42.5] 

1397 [55.0] 

1067 [42.0] 

S2030 

1029 [40.5] 

1397 [55.0] 

1067 [42.0] 

S2034 

1029 [40.5] 

1778 [70.0] 

1067 [42.0] 

K1200 

1029 [40.5] 

978 [38.5] 

787 [31.0] 

K2003

 

1029 [40.5]

 

1397 [55.0]

 

940 [37.0]

 

K2005 

1080 [42.5] 

1397 [55.0] 

940 [37.0] 

K2010 

1130 [44.5] 

1397 [55.0] 

940 [37.0] 

RSM0022501

A

B

C

VEHICLE FLOOR LEVEL

GROUND LEVEL

VEHICLE DOOR OPENING

 

FIGURE 2-1:  DOOR OPENING REQUIREMENTS 

T 

Содержание Ricon K Series
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды