manualshive.com logo in svg

Wabtec Ricon K Series, Руководство по обслуживанию

Поделиться
Скачать
Wabtec Ricon K Series Скачать руководство пользователя страница 16

 

 

2 - 3

32DSKE02.B.1 

INSTALLATION

SEPTEMEBER 2010 

S/K-SERIES EXPORT USE SERVICE MANUAL 

RSM0004100

BOTTOM BRACKET

TWO PER BRACKET ASSEMBLY

TOP BRACKET
(LEVEL WITH VEHICLE FLOOR)

VEHICLE FLOOR LEVEL

VEHICLE STEPWELL

 

FIGURE 2-4:  STEPWELL BRACKET 

b.  Position brackets on stepwell and adjust height of both bracket assemblies so that top bracket is level with 

vehicle floor.  Tighten bracket assembly bolts. 

c.  Verify that lift is fully folded (stowed) with handrails folded tight against vertical arms.  If necessary, use ma-

nual pump. 

             WARNING 

LIFT WEIGHT IS APPROXIMATELY 154-179 KG (340 - 395 LBS.).  USE EXTREME CARE WHEN 
POSITIONING BECAUSE STEPWELL BRACKETS MAY TIP.  THIS PROCEDURE MUST NOT BE 
ATTEMPTED BY ONE PERSON. 

d. Refer 

to 

Figure 2-5

.  With doors fully open, position lift in vehicle doorway so that back of lift is supported 

by vehicle floor, and front of lift is supported by both bracket assemblies. 

RSM0004200

BRACKET ASSEMBLY

LIFT FRONT

VEHICLE FLOOR

LIFT REAR

 

FIGURE 2-5:  BRACKET ASSEMBLY 

e.  Fasten Baseplate to vehicle floor: 

NOTE: 

If Ricon power door operators are used, install them first.  They may influence location of lift. 

•

 

Be certain baseplate is flush against vehicle floor.  The baseplate may be slightly offset in door opening to 
provide proper clearance for passenger seats. 

•

 

Before drilling, verify that lift position does not interfere with closing of vehicle doors or operation of passen-
ger seats. 

•

 

If this lift is being installed in a van with sliding doors, omit the bolts in baseplate holes 7 and 8. 

Содержание Ricon K Series
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды