manualshive.com logo in svg

Wabtec Ricon K Series, Руководство по обслуживанию

Поделиться
Скачать
Wabtec Ricon K Series Скачать руководство пользователя страница 28

 

 

2 - 15

32DSKE02.B.1 

INSTALLATION

SEPTEMEBER 2010 

S/K-SERIES EXPORT USE SERVICE MANUAL 

NOTE: 

Correct positioning of ball joint on inside of rod end attachment bracket. 

c.  Assemble rod end attachment brackets to corresponding platform panels using screws and Loc-TITE blue.

 

           

CAUTION 

Do not lengthen tie rod stud to point where panel will lift off its tab support (at center of lift fork).

d.  Adjust left tie rod assembly.  Adjust tie rod stud until nearly all of link free-play is out by lengthening rod. 

NOTE: 

The left platform panel should be adjusted first so that it is slightly higher than right platform panel.  This will 
ensure proper insertion of left panel joining pin through hole in right platform panel. 

e.  Raise platform to point just before panel joining and adjust right tie rod assembly for proper joining. 
f. 

Lower platform below vehicle floor level. 

NOTE: 

There must be no tension or compression on tie rod assemblies when platform is at, or below, the vehicle 
floor level. 

g.  Stow and deploy lift several times to ensure both platform panels join correctly.  Readjust, if necessary, and 

then tighten lock nuts against ball joints to secure adjustment. 

4. 

K-SERIES PLATFORM FOLDING LINKAGE ADJUSTMENT 

For K-Series with split platforms, the front portion of the platform is connected to the rear portion with a hinge.  
The front portion is folded with linkages located at the right and left sides of the platform.  The length of the lin-
kage might require adjustment after installation of the lift or after disassembly of the platform. 

NOTE: 

Perform the PLATFORM TILT ADJUSTMENT procedure before adjusting the linkage. 

a.  Deploy and lower the platform to a position about halfway between floor level and ground level. 
b. Refer 

to 

Figure 2-19

.  Inspect the gaps on both sides of the platform folding joints.  The gaps must be uni-

form.  If the gaps are not uniform, adjustment is required.  

 

FIGURE 2-19:  S/K-SERIES PLATFORM SET SCREWS 

c. Refer 

to 

Figure 2-20

.  Loosen the jam nuts (right and left sides) and use the adjusters to set the length of 

the linkages so that the front and rear portions are in the same plane; the two surfaces of the platform por-
tions must be flat without any apparent folding along the hinge. 

Содержание Ricon K Series
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды