Wabtec Ricon K Series Скачать руководство пользователя страница 32

Страница: 32 / 79

2 - 19

32DSKE02.B.1

INSTALLATION

SEPTEMEBER 2010

S/K-SERIES EXPORT USE SERVICE MANUAL

a. Deploy and lower platform completely to ground level.

b. Remove pump cover to access release valve.

c. Locate spring and detach from short actuator cable, using pliers.

NOTE:

Detaching cable spring will remove tension on emergency release cable. Turning release valve counter-
clockwise will loosen any tension left on the emergency release cable and allow bolt to be loosened then
removed.

Refer to Figure 2-27

. Loosen the bolt that attaches cable to manual release actuator.

RSM0020500

HYDRAULIC PUMP

MANUAL RELEASE ACTUATOR

MANUAL RELEASE CABLE

(TO MANUAL RELEASE LEVER)

WASHER

BOLT

THREADED INSERT

MANUAL RELEASE CABLE

(TO SPRING)

FIGURE 2-27: MANUAL RELEASE ACTUATOR

e. Remove threaded insert from manual release actuator.

Adjust cable in increments of 3mm (1/8 in.) to 6mm (1/4 in.).

CAUTION

Do not add more tension to cable than is required. Adding too much tension to cable will affect

the operation of the manual release valve and cause the valve to remain in open position.

Manual release valve in open position will cause platform to deploy and lower to ground or can

cause lift to not stow completely.

g. Secure cable to required tension then re-insert manual release threaded insert into manual release actua-

tor.

h. Tighten bolt and ensure that cable is securely fastened with cable located within the groove of manual re-

lease actuator.

Ensure tension on cable does not open manual release valve.

Use pliers and refasten spring to short actuator cable.

k. Raise and completely stow platform.

Refer to Figure 2-26

. Test Emergency Release by placing emergency release lever in “Deploy” position.

Platform should deploy and remain at vehicle floor level.

m. Place Emergency Release lever in “Hold-Open” position. Platform should completely deploy to ground lev-

el.

n. Ensure that platform completely stows when placed in stowed position.

Содержание Ricon K Series
















































































Результаты поиска

Содержание Ricon K Series

Отзывы:

Бренды по названию

Популярные бренды

Wabtec Ricon K Series, Руководство по обслуживанию

Результаты поиска

Содержание Ricon K Series

Отзывы:

Бренды по названию

Популярные бренды