manualshive.com logo in svg

Wabtec Ricon K Series, Руководство по обслуживанию

Поделиться
Скачать
Wabtec Ricon K Series Скачать руководство пользователя страница 36

 

 

3 - 3 

MAINTENANCE 

SEPTEMBER 2010 

32DSKE02.B.1 

S/K-SERIES EXPORT USE SERVICE MANUAL 

D. TROUBLESHOOTING 

The troubleshooting guides are designed to provide logical starting points to locate general problems that could occur 
with lift.  However, not all possible problems or combinations of problems are listed.  For troubleshooting lift, refer to 

Tables 3-2

.  The guide do not incorporate routine safety precautions or preliminary procedures and assume that vehicle 

battery is fully charged and battery terminals/connectors are clean and tight. 

         WARNING 

THE TROUBLESHOOTING GUIDES DO NOT INCORPORATE ROUTINE SAFETY PRECAUTIONS 

OR PRELIMINARY PROCEDURES.  DURING THE RICON WARRANTY PERIOD A TRAINED, 

VAPOR RICON AUTHORIZED DEALER OR QUALIFIED SERVICE TECHNICIAN MUST PERFORM 

TROUBLESHOOTING.  AFTER THE WARRANTY PERIOD, IT IS RECOMMENDED THAT 

TROUBLESHOOTING BE CONTINUED BY A QUALIFIED SERVICE TECHNICIAN.

 

1. LIFT 

TROUBLESHOOTING 

TABLE 3-2:  TROUBLESHOOTING LIFT OPERATION  

SYMPTOM

 

POSSIBLE CAUSE

 

REMEDY

 

Hydraulic fluid leaks

 

Loose hydraulic fitting.

 

Make sure fitting is PROPERLY tightened.

 

 

Hydraulic component  
defective.

 

Discontinue use of lift.  Have repairs made by an authorized 
Vapor Ricon dealer.

 

Rollstop does not open

 

Obstruction of rollstop  
release latch.

 

Raise lift and remove obstruction.

 

Lift  
functions

 

Abnormal  
Operation.

 

Obstruction in lifting frame.

 

Remove obstruction and check for any damage

 

 

 

Backup pump manual release 
valve OPEN.

 

Turn manual release valve CLOCKWISE until slightly snug.

 

 

 

Hydraulic fluid may be low.

 

While platform is at GROUND LEVEL, be certain that pump 
hydraulic fluid level is maintained at required FULL level.  
Add only Texaco 01554 Aircraft Hydraulic Oil or equivalent 
U.S. mil spec H5606G fluid.

 

 

 

Air may be trapped in  
hydraulic system. 

 

Purge hydraulic system by operating lift through its maxi-
mum range of travel for at least four complete cycles. (For 
vehicles that do not use full travel of lift, the maximum range 
of travel is accomplished by raising vehicle on a service 
hoist or ramp.)

 

 

No Operation.

 

Control system circuit breaker 
tripped.

 

Reset circuit breaker.

 

 

 

Backup pump manual release 
valve OPEN.

 

Turn manual release valve CLOCKWISE until slightly snug.

 

 

 

Hydraulic hose or fitting leak.

 

Contact an authorized Vapor Ricon dealer for repair.

 

 

 

Hydraulic fluid may be low.

 

While platform is at GROUND LEVEL, be certain that pump 
hydraulic fluid level is maintained at required FULL level.  
Add only Texaco 01554 Aircraft Hydraulic Oil or equivalent 
U.S. mil spec H5606G fluid.

 

 

 

Air can be trapped in  
hydraulic system. 

 

Purge hydraulic system by operating lift through its maxi-
mum range of travel for at least four complete cycles. (For 
vehicles that do not use full travel of lift, the maximum range 
of travel is accomplished by raising vehicle on a service 
hoist or ramp.)

 

END OF TABLE

 

 

Содержание Ricon K Series
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды