Vollrath STOELTING Flavor Burst STL-40SS-JR Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 74

background image

61

5. Select a numbered tray to correspond with

the flavor you have chosen.

6. Grip the bag underneath the fitment and lift

the bag up, with your other hand supporting
the bottom of the bag. Flip the fitment end
over into the open end of the tray, while
guiding the back end of the syrup bag into
the back end of the syrup tray.

7. Settle the bag into the tray evenly, with the

fitment behind the tray opening.

8. Make sure the syrup bag is settled neatly

into the tray, and then install the loaded tray
into the cabinet.

9. At this time, you may wish to change the

Touch Panel menu flavor names to
coordinate with the new flavors installed.
This may be done now or later in the
TOUCH PANEL OPERATIONS MANUAL.

10. Perform the entire Clean-In-Place

procedure as instructed in the SCHEDULED
MAINTENANCE section. The Clean-In-
Place procedure

MUST

be done during the

initial setup of the STL-40SS-JR to ensure
all the parts and syrup lines are sanitized
and ready for use.

11. After the Clean-In-Place procedure, the

syrup lines will be filled with sanitizer
solution. To prime the syrup lines with the
new syrup flavors, follow the full instructions
outlined in the SCHEDULED
MAINTENANCE – PRIMING THE SYRUP
SYSTEM in the previous section of this
manual.

«
...
62
63
64
65
66
...
»

Содержание STOELTING Flavor Burst STL-40SS-JR











































































Отзывы:

Нет отзывов

Похожие инструкции для STOELTING Flavor Burst STL-40SS-JR

Бренд: Moosoo Страницы: 8

Бренд: brim Страницы: 20

Бренд: HOFFEN Страницы: 40

Бренд: DeLonghi Страницы: 22

Бренд: EdgeStar Страницы: 24

Бренд: Faema Страницы: 244

Бренд: Saeco Страницы: 68

Бренд: Hamilton Beach Страницы: 11

Бренд: Keurig Hot Страницы: 36

Бренд: Menuett Страницы: 77

Бренд: Gaggenau Страницы: 150

Cuisinart Brew Central

Бренд: Costco Страницы: 2

Бренд: DeLonghi Страницы: 12

Бренд: Hyundai Страницы: 36

Бренд: Manitowoc Страницы: 16

Бренд: Manitowoc Страницы: 22

Бренд: U-Line Страницы: 52

Бренд: U-Line Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды