Vollrath STOELTING Flavor Burst STL-40SS-JR Скачать руководство пользователя страница 16

Страница: 16 / 74

Syrup Pump and Related Parts (See Figure 4)

ITEM

PART NO.

DESCRIPTION

QTY.

FUNCTION

N/A

SOFT SERVE SYRUP PUMP
ASSEMBLY

Pumps syrup from flavor bags to flavor lines.

1A STOESYR307

PERISTALTIC SYRUP PUMP

1 ea. Pumps syrup from flavor bags to flavor lines.

1B STOETUB806

1/8” SYRUP PUMP REPL TUBE

1 ea. Transports syrup through pump.

1C STOEFAS2067

SYRUP PUMP TUBE WASHER-1/4

1 ea. Secures pump tube.

1D STOEFAS2066

SYRUP PUMP CLAMP-HOSE-1/4"

1 ea. Prevents pump tube from slipping.

1E STOEFAS2051

ROLLED FLANGE EYELET

1 ea. Creates tension for tighter fit.

1F STOEFIX1036

1/4" TO 1/4" OD UNION ELBOW

1 ea. Connects syrup in tube to pump.

1G STOEFIX1035

1/4 TO 3/16 OD REDUCING UNION

1 ea. Connects syrup pump to flavor line out.

STOESYR944

SYRUP TUBE ASSEMBLY –
SOFT SERVE

Transports flavor from bag to pump.

2A STOEFIX1054

1/4” ID HOSE BARB SHUTOFF

1 ea. Connects flavor line to flavor bag.

2B STOESYR902

FLAVOR-IN TUBE

1 ea. Carries syrup from syrup bag to pump.

2C STOETUB811

TUBE-SILICONE .188X.375 PE
FB80

1 ea. Connects barb fitment to tube port.

2D STOEFIX1048

FITTING-1/4X1/4 BARB FB80

1 ea. Connects syrup tube to silicone tube.

STOESYR927-4

INTERNAL 5-TUBE ASSEMBLY
JUNIOR

Transports syrup from bags to flavor 9-Tube
Assembly.

3A STOESYR900

4' 9-TUBE ASSEMBLY TUBE

Brings syrup from pump to Injector Head.

3B STOEROT511

LINE COUPLER NUT

Connects flavor lines to the internal
9-Tube Assembly.

3C STOEROT512

TUBE CONNECTOR BODY

Connects internal 9-Tube Assembly to
flavor lines.

3D STOEROT510

LINE COUPLER

Holds flavor lines in place.

3E STOEFAS2051

ROLLED FLANGE EYELET

Secures flavor lines to line coupler.

3F STOEMIS3023

FLAVOR LINE DUST CAP

Cover to protect end of flavor lines.

STOECAB113

FLAVORING TRAY

Houses syrup bags.

STOEELE932

PUMP & SANITIZER CABLE
HARNESS

Provides power to the syrup and sanitizer
pumps.

Содержание STOELTING Flavor Burst STL-40SS-JR











































































Результаты поиска

Содержание STOELTING Flavor Burst STL-40SS-JR

Отзывы:

Похожие инструкции для STOELTING Flavor Burst STL-40SS-JR

Бренды по названию

Популярные бренды

Vollrath STOELTING Flavor Burst STL-40SS-JR, Оборудование, техническое обслуживание и эксплуатация: Руководство

Результаты поиска

Содержание STOELTING Flavor Burst STL-40SS-JR

Отзывы:

Похожие инструкции для STOELTING Flavor Burst STL-40SS-JR

Бренды по названию

Популярные бренды