Vollrath STOELTING Flavor Burst STL-40SS-JR Скачать руководство пользователя страница 20

Страница: 20 / 74

Electronic Parts and Connections (See Figure 6)

ITEM

PART NO.

DESCRIPTION

QTY.

FUNCTION

STOEELE906

FLAVOR 10 COLOR TOUCH
PANEL

Control system for the unit.

STOEMIS3214

TOUCH PANEL MOUNTING
BRACKET ASSEMBLY

Secures the Touch Panel to the freezer.

STOEMIS3214A

TOUCH PANEL MOUNTING
PLATE

1 ea. Attaches the Touch Panel to the anchor bracket.

STOEMIS3214B

MOUNTING ANCHOR BRACKET

1 ea. Allows the bracket to be angled up or down.

STOEMIS3214C

MOUNTING BASE PLATE

1 ea.

Creates a mounting base for the bracket
assembly.

STOEFAS2170

M4 X 8 PHILLIPS SCREW

4 ea. Secures the mounting plate to the Touch Panel.

STOEFAS2174

1/4 - 20 NYLON LOCK NUT S.S.

2 ea. Secures the anchor bracket in a fixed position.

STOEMIS3076

ADHESIVE PAD

1 ea. Secures the mounting bracket to the freezer.

STOEFAS2172

1/4-20 X 1/2 HEX BOLT

2 ea. Hinges Touch Panel plate and anchor bracket.

STOEFAS2023

MOUNTING BRACKET KNOB

4 ea. Secures anchor bracket to the base plate.

STOEFAS2171

M4 LOCK WASHER

4 ea. Secures connection between screw and plate.

STOEFAS2173

FLAT WASHER 18-8 S.S.

2 ea. Secures connection between bolt and nut.

STOEELE931

EXTERNAL ROTOR CABLE

Connects the external rotor cable to the
electronics board.

STOEINJ330TS

INJECTOR MOTOR ASSEMBLY

Supplies power to Motor to turns gears.

STOEELE525M

MALE TO MALE 48” SWITCH
EXTENSION

Connects Touch Panel to the freezer switch.

STOECAB137-B

ELECTRONICS COVER

Protects and covers electronics microprocessor.

STOEFAS2014

8-32 X 1/2" PAN HEAD

10 Secures various parts within the top of unit.

STOEMIS3150

FLAVOR BURST LOGO DECAL

Displays Flavor Burst trademark logo.

STOEMIS3026S

TOUCH PANEL CABLE CASING

Conceals and protects the Touch Panel cable, as
well as attaches it to the freezer.

10 STOEELE485CTP

120V POWER ENTRANCE
MODULE

Provides a power connection to the outside of
the cabinet.

10A N/A

GROUNDING WIRE

1 ea. Grounds electricity.

11 STOEELE932

PUMP & SANITIZER CABLE
HARNESS – CTP DLX

Provides power to the syrup and sanitizer
pumps.

12 STOEELE933

POWER SUPPLY JUMPER CABLE

Connects the power supply to the electronics
board.

13 STOEELE911

ELECTRONICS BOARD

Provides power to the system.

14 STOEFAS2024

8-32 X 1/4 PAN HEAD SCREW

Secures electronics board to the base panel.

15 STOEFAS2035

8-32 NUT - EXT. LOCK WASHER

Secures electronics board to base panel and
grounding wire to the cap.

16 STOEMIS3004

CTP ETHERNET CABLE PLATE

Converts the touchscreen cable hole to an
ethernet cable hole.

17 STOEELE930

INTERNAL ROTOR CABLE

Connects the external rotor cable to the
electronics board.

18 STOEFAS2008

4-40 X 3/8" PAN HEAD SCREW

Attaches the ethernet plate to the panel.

19 STOEMIS3166

CLOSURE PLUG 3/4 INCH

Closes up extra opening in the base panel.

20 STOEELE434

POWER CABLE

Supplies the electronics board with power.

21 STOEELE927

RJ45 ETHERNET CABLE GLAND

Secures the Ethernet cable to the cabinet.

22 STOEELE925

RJ45 EHTERNET CABLE - EXTERNAL

Connects the Touch Panel to the cabinet.

Содержание STOELTING Flavor Burst STL-40SS-JR











































































Результаты поиска

Содержание STOELTING Flavor Burst STL-40SS-JR

Отзывы:

Похожие инструкции для STOELTING Flavor Burst STL-40SS-JR

Бренды по названию

Популярные бренды

Vollrath STOELTING Flavor Burst STL-40SS-JR, Оборудование, техническое обслуживание и эксплуатация: Руководство

Результаты поиска

Содержание STOELTING Flavor Burst STL-40SS-JR

Отзывы:

Похожие инструкции для STOELTING Flavor Burst STL-40SS-JR

Бренды по названию

Популярные бренды