Vollrath STOELTING Flavor Burst STL-40SS-JR Скачать руководство пользователя страница 18

Страница: 18 / 74

Sanitizer Pump and Related Parts (See Figure 5)

ITEM

PART NO.

DESCRIPTION

QTY.

FUNCTION

STOEMIS3028-80

FLUSH TUBE ASSEMBLY

Connects with flavor line to flush with
sanitizer solution.

1A STOEFIX1054

1/4” ID HOSE BARB SHUTOFF

1 ea.

Connects to the syrup line to flush sanitizer
solution through it.

1B STOEFIX1051

1/4” ID HOSE BARB ELBOW

1ea.

Connects to the syrup line to flush sanitizer
solution through it.

1C STOESYR931

CLEAR TUBING

3 ea.

Transports sanitizer to Pump Flush Adapter
fitments.

1D STOEFIX1046

FLUSH TUBE “Y” CONNECTOR

1 ea. Splits sanitizer flush tube into two tubes.

STOETUB807

SANITIZER TUBE REPLACEMENT

Transports sanitizer through pump.

STOESAN748

SANITIZER PUMP ASSEMBLY

Supplies sanitizer to flush tube.

STOEELE932

PUMP & SANITIZER CABLE
HARNESS

Provides power to the syrup and sanitizer
pumps.

STOEFIX1035

1/4 TO 3/16 OD REDUCING UNION

Connects elbow to sanitizer line.

STOEFIX1042

TUBE-TO-TUBE ELBOW

Connects pump tube to reducing union.

STOEFIX1053

SANITIZER PUMP T CONNECTOR

Connects sanitizer line to flush adapter
and pump lines.

STOEFIX1023

3/16" X 3/16" BARB TUBE CONNECT

Splices together flush tubes.

STOESYR931

CLEAR TUBING

Transports sanitizer to Pump Flush Adapter.

10 STOETUB803

.17 x 1/4 LDPE TUBING-PER FOOT

Transports sanitizer solution from tank
to sanitizer pump.

11 STOEFIX1033

1/4" X 1/4" BLKHD (PUSH-TO-
CONNECT)

Connects sanitizer tank tube to the unit.

12 N/A

SANITIZER TANK TUBE ASSEMBLY

Transports sanitizer from the tank to the pump.

12A STOEFIX1042

TUBE-TO-TUBE ELBOW

1 ea.

Connects the sanitizer tank tube to the back of
the cabinet.

12B STOESYR931

CLEAR TUBING

1 ea. Transports sanitizer from the tank to the pump.

12C STOEFIX1051

SANITIZER TANK FITMENT

1 ea. Connects sanitizer tube to Sanitizer Tank.

13 STOESAN756

SANITIZER TANK ASSEMBLY

Houses sanitizer cleaning solution.

13A STOESAN749

THREADED CHECK VALVE

1 ea. Allows air to fill Sanitizer Tank.

13B STOESAN750

SANITIZER TANK DOME NUT

1 ea. Mounts check valve to Sanitizer Tank.

13C STOEFIX1052

SANITIZER TANK QUICK
CONNECT

1 ea. Connects sanitizer lines to Sanitizer Tank.

13D STOESAN755

SANITIZER TANK CAP

1 ea. Allows Sanitizer Tank to be refilled.

13E STOESAN754

SANITIZER CAP O-RING

1 ea.

Seals the Sanitizer Tank opening to
prevent leakage.

13F STOESYR931

CLEAR TUBING

1 ea. Transports sanitizer to flush tubes.

13G STOESAN752

SANITIZER TANK

1 ea. Houses sanitizer cleaning solution.

13H STOERUB604

SANITIZER TAINK O-RING

4 ea.

Seals sanitizer tank’s quick connect & check
valve openings.

14 STOESYR927-4

INTERNAL 5-TUBE ASSEMBLY
JUNIOR

Transports syrup from bags to flavor 9-Tube
Assembly.

14A STOESYR900

4' 9-TUBE ASSEMBLY TUBE

Brings syrup from pump to Injector Head.

14B STOEROT511

LINE COUPLER NUT

Connects flavor lines to the internal
9-Tube Assembly.

14C STOEROT512

TUBE CONNECTOR BODY

Connects internal 9-Tube Assembly to
flavor lines.

Содержание STOELTING Flavor Burst STL-40SS-JR











































































Результаты поиска

Содержание STOELTING Flavor Burst STL-40SS-JR

Отзывы:

Похожие инструкции для STOELTING Flavor Burst STL-40SS-JR

Бренды по названию

Популярные бренды

Vollrath STOELTING Flavor Burst STL-40SS-JR, Оборудование, техническое обслуживание и эксплуатация: Руководство

Результаты поиска

Содержание STOELTING Flavor Burst STL-40SS-JR

Отзывы:

Похожие инструкции для STOELTING Flavor Burst STL-40SS-JR

Бренды по названию

Популярные бренды