background image

4

3.1  HOW TO TOP-UP THE SYSTEM PRESSURE 

(

fi

 g. 1-2)

The system pressure must be checked periodically to ensure the 
correct operation of the boiler. The needle on the gauge should 
be reading between 1 and 1.5 BAR when the boiler is in an off 
position and has cooled to room temperature. If the pressure 
requires ‘topping-up’ use the following instructions as a guide.
- Locate the fi lling valve connections (usually beneath the 

boiler, see fi g. 2).

- Attach the fi lling loop to both connections.
- Open the fi lling valve slowly until you hear water entering the 

system.

- Close the fi lling valve when the pressure gauge (on the boiler) 

reads between 1 and 1.5 BAR (see fi g. 1).

- Remove the fi lling loop from the connections.

3.2 HOW TO RESET THE APPLIANCE

When the red fault LED is illuminated, the appliance will require 
to be reset manually. Before resetting the boiler, check what 
action is required to be taken, using the information on the 
fault code table below. Allow a period of two minutes to elapse 
before rotate the mode selector knob across the 

 position 

(see fi g. 1).

IMPORTANT

If the appliance requires to be reset frequently, it may be indica-
tive of a fault, please contact your installer or Vokèra Customer 
Services for further advice.

3.3 HOW TO SHUT DOWN THE SYSTEM FOR SHORT 
PERIODS

The system and boiler can be shut down for short periods by 
simply turning the time clock to the off position. It is also advis-
able to turn off the main water supply to the house.

3.4 HOW TO SHUT DOWN THE SYSTEM FOR 

LONG PERIODS 

If the house is to be left unoccupied for any length of time – 
especially during the winter – the system should be thoroughly 
drained of all water. The gas, water, and electricity supply to 
the house should also be turned off. For more detailed advice 
contact your installer.

3.5 HOW TO CARE FOR THE APPLIANCE 

To clean the outer casing use only a clean damp cloth. Do not 
use any scourers or abrasive cleaners.

3. HOW TO...

Fig. 2

control 

valve

temporary 

connection

control 

valve

supply pipe

double 

check valve

fl ow/return 

pipe

4.1 WHAT IF I SUSPECT A GAS LEAK

If you suspect a gas leak, turn off the gas supply at the gas 
meter and contact your installer or local gas supplier. If you 
require further advice please contact your nearest Vokèra offi ce.

4.2 WHAT IF I HAVE FREQUENTLY TO TOP-UP 
THE SYSTEM

If the system regularly requires topping-up, it may be indicative 
of a leak. Please contact your installer and ask him to inspect 
the system.

4.3 WHAT IF THE APPLIANCE IS DUE ITS AN-

NUAL SERVICE

 

Advice for tenants only

Your landlord should arrange for servicing.

Advice for homeowners

Please contact Vokèra Customer Service 

(0844 3910999 (UK) 

or 056 7755057 (ROI)

 if you would prefer a Vokèra service 

engineer or agent to service your appliance. Alternatively your 
local GAS SAFE registered engineer may be able to service 
the appliance for you.

4.4 - WHAT IF I NEED TO CALL AN ENGINEER

If you think your boiler may have developed a fault, please contact 
your installer or Vokèra Customer Services 

(0844 3910999 (UK) 

or 056 7755057 (ROI)

 have all your details to hand including 

full address and postcode, relevant contact numbers, and your 
completed appliance log book.

4. WHAT IF...

Содержание Mynute i20









































Отзывы: