Vixen AP Equatorial Mount Скачать руководство пользователя страница 65

Страница: 65 / 72

APPLICATION

Mount head unit

DEC motor module

4mm Allen wrench

3mm Allen wrench

Electrical contact

While holding the declination body, attach the declination body

securely with the two supplied M5-25mm long screws using the 4mm

Allen wrench.

Attach the AP clamp mount head unit onto the DEC motor module

with the electrical contact on the outside so that the central protruding

portion of the AP clamp mount head fits snugly onto the central hollow

portion of the DEC motor module as shown in the figure.

Turn the DEC motor module to change the orientation so that the

screw holes (larger holes with no thread) are aligned in tandem. Attach

the DEC motor module with the three supplied socket head cap

screws securely using the 4mm Allen wrench.

Attach the DEC motor module assembly onto the declination body so

that the electrical contact on the DEC motor module fits snugly onto

the counterpart on the declination body as shown in the figure.

Caution:

The internal joint electrical contact of the declination body is very
delicate. Take care not to touch with fingers or other objects.

Содержание AP Equatorial Mount









































































Результаты поиска

Содержание AP Equatorial Mount

Отзывы:

Похожие инструкции для AP Equatorial Mount

Бренды по названию

Популярные бренды

Vixen AP Equatorial Mount, Инструкция по эксплуатации

Результаты поиска

Содержание AP Equatorial Mount

Отзывы:

Похожие инструкции для AP Equatorial Mount

Бренды по названию

Популярные бренды