Vixen AP Equatorial Mount Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 72

background image

20

-

PREPARATION

Attaching the Dovetail Slide Bar

AP Photo Guider

Safety screw

Safety screw

Back off

Dovetail plate
lock screw

Dovetail plate
lock screw

Stopper

Stopper

Set screw

Set screw

Set screw

4mm Allen wrench

Tip of the lock screw

1

Loosen both the dovetail plate lock screw and safety screw on
the mount head fully so that space is available for the dovetail
slide bar.

2

Attach the dovetail slide bar to the mount head so that the
dovetail slide bar fits securely into the sunken mount head.

Orientate the dovetail slide bar as shown in the figure to pre-
vent the dovetail slide bar from falling. (The dovetail slide bar
has a stopper screw on one side of the dovetail rail.) Attach
the dovetail slide bar so that the tip of the dovetail plate lock
screws hits on another part of the dovetail rail with no stopper
screws.

3

First tighten the dovetail plate lock screw onto the dovetail
slide bar centering notch until it is snug. Then, securely tighten

the safety screw.

The mount head unit is attached onto the head of the polar axis body
aseembly with three set screws that are equally put on its side. The
set screws can be loosened with the 4mm Allen wrench to change
the position of the mount head to pint at your desired orientation.

About the orientation of the mount head unit

«
...
18
19
20
21
22
...
»

Содержание AP Equatorial Mount









































































Отзывы:

Нет отзывов

Похожие инструкции для AP Equatorial Mount

Бренд: VDO Страницы: 91

Бренд: CALEFFI Страницы: 20

Бренд: Barco Страницы: 25

Бренд: Barco Страницы: 16

Бренд: Camcar Страницы: 6

Бренд: DataCard Страницы: 2

Бренд: DataCard Страницы: 24

ImageCard series

Бренд: DataCard Страницы: 2

ImageCard series

Бренд: DataCard Страницы: 2

CYCLO 315 Series

Бренд: Magellan Страницы: 39

Бренд: MadStad Engineering Страницы: 2

Бренд: Yealink Страницы: 6

Бренд: Panasonic Страницы: 4

Бренд: Daikin Страницы: 52

Бренд: Lanner Страницы: 78

Бренд: Ericsson Страницы: 487

Ocean Seven 304Plus

Бренд: idronaut Страницы: 79

Бренд: media-tech Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды