manualshive.com logo in svg

Vitrek 951i, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Vitrek 951i Скачать руководство пользователя страница 10

95x Series Operating Manual - May 17, 2022 

Page 

10

 of 

155

 

 

WARRANTY INFORMATION 

This Vitrek instrument is warranted against defects in material and workmanship for a period of 1 year after the 
date of purchase (extended up to a total of 3 years with registration and annual calibrations at Vitrek).  Vitrek 
agrees to repair or replace any assembly or component (except batteries) found to be defective, under normal use, 
during the warranty period.  

Vitrek’

s obligation under this warranty is limited solely to repairing any such 

instrument, which in 

Vitrek’

s sole opinion proves to be defective within the scope of the warranty, when returned 

to the factory or to an authorized service center.  Transportation to the factory or service center is to be prepaid by 
the purchaser.  Shipment should not be made without prior authorization by Vitrek. 

This warranty does not apply to any products repaired or altered by persons not authorized by Vitrek or not in 
accordance with instructions provided by Vitrek.  If the instrument is defective as a result of misuse, improper 
repair, improper shipment, or abnormal conditions or operations, repairs will be billed at cost. 

Vitrek assumes no responsibility for its products being used in a hazardous or dangerous manner, either alone or in 
conjunction with other equipment.  Special disclaimers apply to this instrument.  Vitrek assumes no liability for 
secondary charges or consequential damages, and, in any event, 

Vitrek’

s liability for breach of warranty under any 

contract or otherwise, shall not exceed the original purchase price of the specific instrument shipped and against 
which a claim is made. 

Any recommendations made by Vitrek or its representatives, for uses of its products are based on tests believed to 
be reliable, but Vitrek makes no warranties of the results to be obtained.  This warranty is in lieu of all other 
warranties, expressed or implied and no representative or person is authorized to represent or assume for Vitrek 
any liability in connection with the sale of our products other than set forth herein. 

 

Document number MO-95x-GOM revision H, 26 June 2016. 

Copyright© 2009-2015 Vitrek.   

All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval 
system, or translated into any language in any form without prior written consent from Vitrek.  This document is 
copyrighted and contains proprietary information, which is subject to change without notice.  The product displays 
and instructional text may be used or copied only in accordance with the terms of the license agreement. 

In the interest of continued product development, Vitrek reserves the right to make changes in this document and 
the product it describes at any time, without notice or obligation. 

Vitrek 
12169 Kirkham Road, 
Poway, CA 92064 USA 
Telephone: 858-689-2755 
Fax : 858-689-2760 
Web : 

www.Vitrek.com

 

Email : 

[email protected]

 

 

 

Содержание 951i




























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды