Vitek VT-1193, Инструкция по эксплуатации

Страница: 5 / 32

5
ENGLISH
up. The display (17) will show the keep warm
temperature (18) and the water temperature
in the thermopot (19).
Notes:
–
the thermopot uses a long boiling technology
which allows to significantly reduce the chlo-
rine level in water.
–
every pressing of the control buttons is
accompanied with a sound signal.
–
after pressing the control buttons the water
level scale illumination lights up and goes out
after 30 seconds.
•
Drain the water; to do this, you must unlock
the activation of the water pump by pressing
button (24) « UNLOCK», the light indicator
« UNLOCK» will light up.
Attention! Be careful when pouring out water to
avoid burns by hot water.
Version 1:
–
place a suitable bowl, for instance, a cup
under the spout for pouring water (4) and
press the water dispense button (3) with a rim
of the cup.
Version 2:
–
place a suitable bowl under the spout for
pouring water (4) and press the water dis-
pense button (23) «DISPENSE».
Notes:
–
the button (24) « UNLOCK» and the button
(23) «DISPENSE» are sensory, you just need
to touch them.
–
the water is dispensed only when the indica-
tor (24) « UNLOCK» is switched on; if you
pressed the button (24) « UNLOCK» and
didn’t do anything, the indicator (24) will go
out in 10 seconds.
•
To switch the thermopot off disconnect the
power plug (16) from the mains socket.
•
To switch the thermopot off disconnect the
power plug (16) from the mains socket.
• Open the thermopot lid (8) and wait until it
cools down completely.
•
Before removing the lid (8) open it and pull the
lid (8) to the control panel (5).
•
Carefully tilt the thermopot to drain the
remaining water.
•
Install the lid (8) in the lock (9). To do it, place
the lid (8) at a small angle and insert the lid (8)
into the lock (9). Before using the thermopot
make sure that the lid (8) is fixed properly.The
thermopot is ready for operation.
USAGE OF THERMOPOT
•
Open the lid (8) by pressing the button (6) and
holding it.
•
Fill the thermopot with water using a suitable
bowl, do not exceed the maximal water level
mark (15) «FULL».
•
Insert the power cord (16) connector into the
socket (12) on the thermopot body, and the
power cord (16) plug into the mains socket,
you will hear a sound signal. The thermopot
will switch on in the boiling mode, the indi-
cator (25) «BOILING» will light up. The water
level scale (2) illumination will light up, the dig-
ital symbols (18) on the display (17) will show
the keep warm temperature «85». The digital
symbols (19) will show the water temperature
in the thermopot.
Notes: - water temperature (19) is shown from
25°С to 100°С with a step 5°С.
• The keep warm temperature «85°» is set by
default.
•
After long water boiling you will hear sound sig-
nals and the thermopot will switch to the keep
warm mode, the indicator (25) «BOILING» will
go out and the keep warm mode indicator (22)
«KEEP WARM» will light up.
•
When the water in the thermopot cools down
below 85°, the indicator (25) will light up and
the water temperature will be maintained.
•
If the water temperature goes significantly
below the preset temperature, for instance,
if you added some cold water, the boiling
mode will be switched on, the indicator (25)
«BOILING» will light up. After boiling the water
temperature will be maintained depending on
the preset value and will be shown with the
digital symbols (19).
•
To change the required keep warm tempera-
ture press the water temperature setting but-
ton (21) «TEMP.SELECT». You can select the
keep warm temperature «95, 85, 65, 55, 40,
-- (room temperature)».
•
Recommended temperature for brewing tea
and making other beverages:
–
«40°» – water temperature for powdered
baby milk
–
«85°» – green and yellow tea
–
«95°» – black tea
IM VT-1193.indd 5 11/26/19 2:32 PM