Vislink HDT-1000 Скачать руководство пользователя страница 52

Страница: 52 / 62

Page 52

HDT-1000 User and Technical Manual

DC Power

Source

Viewing Two Video Streams Simultaneously

In order to view two video streams simultaneously, you will need both an HDR-1000

Receiver and HDR-DV Decoder.

Complete the following steps to set up your HDR-1000 Receiver and HD-DV Decoder

to receive two video streams simultaneously.

1. Connect one monitor to either video output of the HDR-1000 Receiver.
2. Connect a second monitor to either video output of the HD-DV Decoder.

3. Connect a BNC Connector Cable between the Diversity/ASI Out Connector on the

HDR-1000 Receiver and the ASI In Connector on the HD-DV Decoder.

Connect your resonant antennas to the RF IN connectors on the HDR-1000

Receiver.

Make DC Power In connections to both units via the LEMO Power Connectors.

6. Complete the Transmitter Setup and Receiver Setup instructions given in this

section for the Web Browser Control Interface.

7. Setup the HD-DV Decoder to the same active Preset as the Receiver.

NOTE

The HDR-DV Decoder behaves like a second HDR-1000 Receiver

(without the RF section) in the Web Browser Control Interface.

Antenna 1

Antenna 2

Video

Monitor

Video

Monitor

Содержание HDT-1000































































Результаты поиска

Содержание HDT-1000

Отзывы:

Похожие инструкции для HDT-1000

Бренды по названию

Популярные бренды

Vislink HDT-1000, Руководство пользователя и техническое руководство

Результаты поиска

Содержание HDT-1000

Отзывы:

Похожие инструкции для HDT-1000

Бренды по названию

Популярные бренды