Vislink HDT-1000 Скачать руководство пользователя страница 13

Страница: 13 / 62

Page 13

HDT-1000 User and Technical Manual

Menu Bar

Navigating the Web Browser Control Interface is accomplished by clicking on a menu

option in the

Menu Bar

. For example, to go to the

Change Password

screen you would

navigate to

System

Password Change

as shown.

Change Password

The transmitter is factory programmed with the user name

root

and password

root

To avoid unauthorized access, the factory assigned password should be changed by

selecting

System

Password Change

from the menu bar.

Enter your new password in the

New Password

field. The case sensitive password can

be up to 18 alphanumeric characters in length. Enter the new password in the

Confirm

Password

field then click the

Change Password

button.

NOTE

Be sure to remember your new password.

menu bar

Содержание HDT-1000































































Результаты поиска

Содержание HDT-1000

Отзывы:

Похожие инструкции для HDT-1000

Бренды по названию

Популярные бренды

Vislink HDT-1000, Руководство пользователя и техническое руководство

Результаты поиска

Содержание HDT-1000

Отзывы:

Похожие инструкции для HDT-1000

Бренды по названию

Популярные бренды